LTECH D40 DMX512 Decoder Instruction Manual

Pesteview

Afișaj OLED
8 biți / 16 biți
4 kinds of DMX interfaces
Dimming curve: 0.1-9.9
Short circuit / Over current / Overheat protection

D40
DMXS12 DCODER

Prezentarea produsului

1. Designed for Hi-power multiple channels application, 40 channels output, and Max. 3A current per
   channel, up to 2880W output power.
2. The human-computer interaction interface is composed of an OLED screen and 3 buttons, which
   displays rich content and is simple and fast to operate.
3. The number of DMX channels can be set to CH01/CH02/CH03/CH04/CH05/CH08/CH16/CH24/
   CH32/CH40, which can realize independent address independent channel control, or one address
   to control multiple channels.
4. The PWM frequency can be set to 300/600/1200/1500/1800/2400/3600/7200/10800/14400/
   18000 Hz;
5. 3-pin XLR, 5-pin XLR, RJ45 and green terminal DMX interface with photoelectric isolation,
   improve signal transmission efficiency and anti-interference ability, the green terminal also has
   semnal ampfuncția de eliminare.
6. With the operations can be completed via the RDM master console, such as parameters browsing
   & settings, DMX address settings, equipment recognition, etc.
7. DMX master control mode；
8. With firmware upgrade function.
9. With short circuit, over current and over temp. protection, as well as warning function when a fault
   apare.
10. With power-on state management and fast self-testing function.
11. 16bit (65536 levels) / 8bit (256 levels) grey level available.
12. Available for standard, linear, LOG or custom 0.1-9.9 dimming curve.
13. The device has 10 built-in personalized lighting effects. You can enter the setting interface of the
    DMX master mode and select different lighting effects to achieve precise output control of other
    decodoare.
14. Parameters can be set and modified through the RDM master control or mobile phone APP,
    eliminating the need for high-altitude operations.

Specificatii tehnice

Dimensiunea produsului

Main component description

OLED screen interface

Schema de cablare

1. Connecting LED lights:

2. DMX Decoder Mode
D40 is equipped with DMX terminals for users’ selection. The following diagram takes 3-pin XLR as an
example, same connecting method for the rest three: Rj45 & 5-pin XLR & green terminal (with ampfuncția de eliminare).

3. Mod de control DMX

• If the recoil effect occurs because of longer signal line or bad line quality, please try to connect
  0.25W 90-120Ω terminal resistor at the end of each line.

4. The connection diagram of 4 kinds of DMX/RDM terminals:

These 4 terminals can be connected in a mixed way.

• Installation attentions: Please reserve enough ventilation distance between decoders (>20mm),
  be sure not to block the vent, or it will affect lifetime of decoder for poor heat dissipation.

5. The connection diagram of AMP semnal ampterminal de separare:

• Connecting with green terminal or an extra amplifier will be needed when more than 32 decoders
  are connected or use overlong signal wire (as shown below).Signal amplifier should not be more
  than 5 times continuously.

8bit Address setting table

9

10

16bit Address setting table

11

Work with RDM editor

D40 can work with LTECH RDM editor (Model: WiFi-RDM01) to realize changing
the parameters by long-range setting, wiring diagram as below:

RDM editor App interface instruction

Download the App, setting the D40 parameters (frequency, bit, curve, modes, dimming range,
screensaver, etc.) after well connecting the RDM editor, more details, please check the manual
of WiFi-RDM01.

Well installation of products first, then working with WiFi -RDM01 to realize setting parameters
and firmware upgrade by App.

a: Click “Add”, edit the address in corresponding box.
b: Click “ID”, get more product details.
c: Click ” “, enter edited interface.
d: Click “No.”, issue the recognizing command.

Supporting WiFi-RDM01 upgrade
and DMX driver upgrade.

Atenţie

• Instalarea și punerea în funcțiune a produsului trebuie efectuate de un profesionist calificat.
• Our company products are and not lightning proof non-waterproof(special models excepted).
  Please avoid the sun and rain. When installed outdoors, please ensure they are mounted
  in a waterproof enclosure or in an area equipped with lightning protection devices.
• O bună disipare a căldurii va prelungi durata de viață a produselor. Vă rugăm să asigurați o bună ventilație.
• Vă rugăm să verificați dacă volumul de lucrutage used complies with the parameter requirements of
  produse.
• The diameter of wire used must be able to load the light fixtures you connect and ensure
  the firm wiring.
• Before you power on products, please make sure all the wiring is correct in case of
  incorrect connection that causes damage to light fixtures.
• If a fault occurs, please do not attempt to fix products by yourself. If you have any
  question, please contact your suppliers.

Acord de garanție

• Perioade de garanție de la data livrării: 5 ani.
• Serviciile gratuite de reparații sau înlocuiri pentru probleme de calitate sunt furnizate în perioadele de garanție.

Excluderi de garanție de mai jos:
Following conditions are not within the guarantee range of free repairing or replacement
servicii:

• Dincolo de perioadele de garanție.
• Orice daune artificiale cauzate de volum maretage, suprasarcină sau operațiuni necorespunzătoare.
• Produse cu daune fizice grave.
• Pagubele cauzate de calamități naturale și forță majoră.
• Etichetele de garanție și codurile de bare au fost deteriorate.
• No any contract signed by our company.

1. Repair or replacement provided is the only remedy for customers. Our company is
   not liable for any incidental or consequential damage unless it is within the law.
2. Our company has the right to amend or adjust the terms of this warranty, and
   release in written form shall prevail.

• This manual is subject to changes without further notice. Product functions depend on the
  goods. Please feel free to contact our official distributors if you have any question.