CITADEL MESH
MIDI TOWER CASE
MANUAL DE UTILIZARE
Cuprins
ascunde
CONținutul pachetului de accesorii
DEMONTAREA PANOULUI
DEMONTAREA PANOULUI FRONTAL/LATERAL
- Take off the front panel by pulling carefully from the bottom of the panel
- Remove the left side panel by pulling on the pull tab & swinging the door outwards, then lift off the hinges at the back of the case.
- Remove the right side pane by removing the two rear thrum screws and sliding the panel backwards
MOTHERBOARD INSTALLA
INSTALAREA PLACII DE MARE
- Align your motherboard with the chassis to locate where the stand-offs should be installed Once done, remove the motherboard and fasten stand-offs accordingly
- Insert your motherboard I/O plate into the cutout at the rear of the case
- Place your motherboard into the chassis, making sure the rear ports fit into the I/O plate
- Use the provided motherboard screws to attach your motherboard to the chassis
INSTALARE SURSA DE ALIMENTARE
INSTALARE SURSA DE ALIMENTARE
- Place PSU in the bottom rear of the case, within the PSU shroud
- Aliniați găurile și fixați cu șuruburi
INSTALARE CARD GRAFICA/CARD PCI-E
INSTALARE CARD GRAFICA/CARD PCI-E
- Scoateți capacele slotului PCI-E din spate după cum este necesar (în funcție de dimensiunea slotului cardului dvs.)
- Carefully position and slide your PCI-E card into place, then secure with the add-on card screws supplied If mounting vertically, attach the vertical GPU mount to the PSU shroud, attach the Klink PCI-E Riser Cable (Sold separately). remove the rear PCI-E slot covers and put the card into place, mounting to the PCI-E Riser cable mount securely
- Remember to attach the other end of the PCI-E Riser cable to your motherboards PCI-E 16x slot
2.5″ SDD INSTALLATION (F)
INSTALARE SSD de 2.5 inchi (FRONT)
- Align your drive over the screw holes and secure with screws from the rear
INSTALARE SDD de 2.5 inchi (R)
INSTALARE SSD de 2.5″ (spate)
Place your SSD on top of the HDD bracket and secure with screws
INSTALARE HDD 3.5″
INSTALARE HDD 3.5″
- Slide the drive into/onto the 3,5″ bay at the rear of the case
- Secure the drive on the both sides using the provided screws and hand tighten
INSTALARE SUPERIOR VENTILATOR
INSTALARE SUPERIOR VENTILATOR
- Remove the dust filter from the top of the case
- Align your fan(s) to the screw holes on the top of the chassis and secure with screws
- Replace your dust filter once secured
INSTALARE VENTILATOR FAȚĂ/SPATE
INSTALARE VENTILATOR FAȚĂ/SPATE
- Align your fan to the screw holes on the chassis and secure with screws
INSTALARE RADIATOR DE RĂCIRE CU APĂ
INSTALARE RADIATOR DE RĂCIRE CU APĂ
- Fixați ventilatoarele la radiator, apoi fixați radiatorul în interiorul șasiului fixând cu șuruburi din exterior
INSTALARE PANOUL I/O
INSTALARE PANOUL I/O
Carefully check the labelling of each connector from the 1/0 panel to identify their function
Cross reference with the motherboard manual to locate where each wire should be installed, then secure one at a time, Please ensure they are installed in the correct polarity to avoid non-function or damage
Documente/Resurse
 |
Carcasă KOLINK ANL-INT Citadel Mesh Midi Tower [pdfManual de utilizare ANL-INT, ANL-INT Carcasă Citadel Mesh Midi Tower, Carcasă Citadel Mesh Midi Tower, Carcasă Midi Tower din plasă, Carcasă Midi Tower, Carcasă Tower |