EKWB EK-Quantum Velocity 3 CPU Water Block User Manual

1. Introducere

This manual provides instructions for the installation, operation, and maintenance of the EKWB EK-Quantum Velocity 3 CPU Water Block. This high-performance water block is designed for liquid cooling systems on AMD AM5 and Intel LGA 1700/1851 platforms, offering efficient heat transfer for demanding computing environments.

Imaginea 1.1: Sus view of the EK-Quantum Velocity 3 CPU Water Block in white, featuring the EK logo and 'Velocity3' branding.

2. Conținutul pachetului

Verificați dacă toate componentele sunt prezente înainte de a începe instalarea:

• EK-Quantum Velocity 3 CPU Water Block
• AMD AM5 Mounting Brackets
• Intel LGA 1700/1851 Mounting Brackets
• Pastă termică EK-Loop NGP (1g)
• Cheie hexagonală de 2.5 mm
• Required mounting hardware (screws, springs, washers)

Imaginea 2.1: Explodată view illustrating the various components of the water block and its mounting hardware.

3. Informații de siguranță

• Siguranta electrica: Asigurați-vă că sistemul computerului este oprit și deconectat de la priza de perete înainte de instalare sau întreținere.
• Manipularea lichidelor: Use only approved coolants for liquid cooling systems. Avoid contact with skin and eyes. In case of contact, rinse thoroughly with water.
• Manipularea componentelor: Handle the CPU water block and other computer components with care to prevent damage. Avoid touching the cold plate surface directly.
• Instalare profesionala: If you are unsure about any step of the installation process, consult a qualified technician or refer to EKWB's official support resources.
• Testarea scurgerilor: Always perform a leak test for at least 24 hours before powering on your system after installing new liquid cooling components.

4. Configurare și instalare

This section outlines the general installation procedure. For detailed, up-to-date instructions and specific motherboard considerations, always refer to the official EKWB installation manual available on their website. Incorrect installation can lead to component damage.

4.1. Pregătire

1. Opriți computerul și deconectați-l de la sursa de alimentare.
2. Remove your existing CPU cooler and clean any residual thermal paste from the CPU IHS (Integrated Heat Spreader) using isopropyl alcohol and a lint-free cloth.
3. Identify the correct mounting bracket for your CPU socket (AMD AM5 or Intel LGA 1700/1851). The water block may require internal re-orientation for optimal flow depending on the platform. Consult the official EKWB guide for this step.

4.2. Instalarea suportului de montare

Attach the appropriate mounting bracket to the water block. Ensure the bracket is oriented correctly for your motherboard and CPU socket type.

Image 4.1: AMD AM5 Mounting Bracket Dimensions. Verify compatibility with your motherboard.

Image 4.2: Intel LGA 1700 Mounting Bracket Dimensions. Verify compatibility with your motherboard.

Important Note for AM5 Users:

Some AM5 motherboards may have protruding screw mounts that affect mounting pressure. It is crucial to ensure proper contact between the water block's cold plate and the CPU IHS. Refer to EKWB's official installation guides for specific AM5 motherboard compatibility and any necessary adjustments to avoid damage to your CPU or motherboard.

4.3. Thermal Paste Application

1. Apply a small amount of the included EK-Loop Thermal Paste NGP to the center of the CPU IHS.
2. Spread the thermal paste evenly across the entire surface of the IHS using a non-conductive spreader or a clean finger in a thin, uniform layer.

4.4. Montarea blocului de apă

1. Carefully place the water block onto the CPU, aligning the mounting holes with the motherboard's backplate or standoffs.
2. Secure the water block using the provided screws, springs, and washers. Tighten the screws in a diagonal pattern (e.g., top-left, bottom-right, top-right, bottom-left) gradually until snug. Do not overtighten.
3. Ensure even mounting pressure for optimal thermal contact.

Imaginea 4.3: Partea de jos view of the water block, highlighting the cold plate and mounting points.

4.5. Connecting to the Liquid Cooling Loop

1. Install appropriate fittings (not included) into the G1/4" ports on the water block. Ensure they are tightened securely to prevent leaks.
2. Connect the water block into your custom liquid cooling loop. The recommended flow direction is typically into the center port and out of the side port, but the block is designed to perform well in either orientation.

4.6. D-RGB Connection

The EK-Quantum Velocity 3 features addressable RGB (D-RGB) lighting. Connect the 3-pin 5V digital LED header cable to a compatible D-RGB header on your motherboard or a dedicated D-RGB controller.

• Lungime cablu D-RGB: 500 mm
• D-RGB connector: 3-pin 5V digital LED header (Pinout: +5V | Digital | Blocked | Ground)

Image 4.4: Water block with D-RGB lighting active (red).

Image 4.5: Water block with D-RGB lighting active (blue).

5. Instrucțiuni de utilizare

Once the water block is installed and integrated into your liquid cooling loop, and a successful leak test has been performed, you can power on your system.

1. Pornirea sistemului: Porniți computerul.
2. BIOS/UEFI Check: Verify that your CPU temperature readings are normal in your system's BIOS/UEFI.
3. Monitorizare software: Use monitoring software (e.g., HWMonitor, AIDA64) to observe CPU temperatures under idle and load conditions.
4. Control D-RGB: If connected to a motherboard header, use your motherboard's RGB software to customize the lighting effects. If connected to a dedicated controller, use its respective software or physical controls.

The EK-Quantum Velocity 3 is designed for continuous operation within a properly maintained liquid cooling system. Monitor your system's temperatures regularly to ensure optimal performance.

6. Întreținere

Regular maintenance is crucial for the longevity and performance of your liquid cooling system and the EK-Quantum Velocity 3 water block.

• Înlocuirea lichidului de răcire: Înlocuiți lichidul de răcire din circuit la fiecare 6-12 luni sau conform recomandărilor producătorului lichidului de răcire.
• Spălare sistem: Periodically flush your entire liquid cooling loop to remove any accumulated debris or residue.
• Water Block Cleaning: If performance degrades or visible buildup occurs, the water block can be disassembled for cleaning. Use distilled water and a soft brush to clean the micro-fins. Avoid abrasive materials. Refer to EKWB's official guides for disassembly and reassembly procedures.
• Inspecție vizuală: Regularly inspect tubing, fittings, and the water block for any signs of leaks, corrosion, or damage.

7. Depanare

8. Specificații

• Model: EK-Quantum Velocity 3
• Număr piesa: 3831109881132
• Compatibilitate socket CPU: AMD AM5, Intel LGA 1700, Intel LGA 1851
• Materiale: Nickel-plated copper cold plate, CNC-machined POM Acetal top
• Dimensiuni: 69 x 69 x 25.1 mm (2.72" L x 2.72" l x 0.99" Î)
• Conector D-RGB: 3-pin 5V digital LED header (Pinout: +5V | Digital | Blocked | Ground)
• D-RGB Cable Length: 500mm
• Metoda de racire: Lichid
• Tip conector de alimentare: 3-Pin (for D-RGB)
• Dispozitive compatibile: Desktop

9. Garanție și asistență

EK Water Blocks products are manufactured to the highest standards. For warranty information, technical support, and the most current installation guides, please visit the official EKWB website-ul.

Official EKWB Website: www.ekwb.com/support

Vă rugăm să păstrați dovada achiziției pentru cererile de garanție.