Manual de utilizare ANENG GN602 Umidificator tip stilou pentru lemn și materiale de construcții

1. Produs terminatview

The ANENG GN602 is a portable, pen-type digital moisture meter designed for quick and accurate measurement of moisture content in various materials, including wood, lumber, concrete, bricks, and other building materials. Its compact design makes it suitable for woodworking, water damage restoration, construction, and home improvement projects.

Caracteristici cheie:

• Pen-Type Design: Convenient pocket-sized form factor for portability.
• High-Precision Pins: Equipped with two sensitive pins for swift and accurate readings.
• Dual Modes & 7 Calibration Scales: Offers two measurement modes and seven material calibration scales for diverse wood types and construction materials, covering a moisture range from 0.0% to 58%.
• Funcția de păstrare a datelor: Allows retention of current readings for stable and precise recording.
• Ecran LCD iluminat din spate: Asigură o vizibilitate clară a citirilor în diverse condiții de iluminare.
• Eficient energetic: Features automatic shutdown after 10 minutes of inactivity to conserve battery life.
• Indicator baterie descărcată: Displays an icon to remind users of timely battery replacement.

Figure 1: ANENG GN602 Pen-Type Moisture Meter with its protective cap removed, showing the measurement pins and the digital display. Two AAA batteries are shown alongside the device.

2. Configurarea și instalarea bateriei

Before using the ANENG GN602 moisture meter, ensure that the batteries are correctly installed.

2.1. Instalarea bateriei

1. Localizați capacul compartimentului bateriei pe spatele dispozitivului.
2. Open the cover by sliding or gently prying it off.
3. Introduceți două baterii AAA de 1.5 V, asigurându-vă că polaritatea este corectă (+/-), așa cum este indicată în interiorul compartimentului.
4. Puneți bine capacul compartimentului bateriei.

2.2. Verificare inițială

After battery installation, power on the device. The display should illuminate. The meter features a self-check function built into the protective cap. To perform a self-check:

1. Ensure the protective cap is placed over the measurement pins.
2. Gently push the pins through the designated pin holes on the outer top of the cap.
3. The meter should display a reading of approximately 20.5% RH. If this reading is shown, the meter is calibrated correctly and ready for use.

Figure 2: The ANENG GN602 Moisture Meter illustrating its pen-type design and pocket-sized portability, along with a visual representation of its 7 material modes for different types of wood and building materials.

3. Instrucțiuni de utilizare

3.1. Pornire/Oprire

• Apăsați tasta Buton de pornire pentru a porni contorul.
• The meter will automatically shut down after 10 minutes of inactivity to conserve battery life.

3.2. Selecting Material Mode

The meter offers 7 calibration scales (modes) for different materials. To select the appropriate mode:

• Apăsați tasta Butonul „M” to cycle through the available material modes (Mode 1 to Mode 7).
• Refer to the user manual's material chart (not provided in this extract, but typically found in the full manual) to match the mode number with your specific material (e.g., oak, pine, concrete, brick).

Figure 3: The ANENG GN602 Moisture Meter shown in various application scenarios, including wood processing, plank processing, measuring firewood, and detecting moisture on a wall surface.

3.3. Luarea unei măsurători

1. Scoateți capacul de protecție de pe știfturile de măsurare.
2. Select the appropriate material mode using the 'M' button.
3. Carefully insert the two measurement pins into the material you wish to test. Ensure both pins penetrate the surface adequately for an accurate reading.
4. The moisture content percentage va fi afișat pe ecranul LCD.

3.4. Funcția de memorare a datelor

• Apăsați tasta 'MAX/MIN' button briefly to activate the data hold function. The current reading will be frozen on the display.
• Press the 'MAX/MIN' button again to release the hold and resume live measurements.
• Holding the 'MAX/MIN' button will display the maximum or minimum recorded values.

3.5. Controlul luminii de fundal

• Apăsați tasta buton luminos (often integrated with the power button or a separate button with a light bulb icon) to turn the LCD backlight on or off. This improves visibility in low-light conditions.

Figure 4: Comparison of the ANENG GN602 Moisture Meter's display with the backlight turned on (left) and off (right), demonstrating improved readability in darker environments.

4. Întreținere

• curatenie: Wipe the meter with a dry, soft cloth. Do not use abrasive cleaners or solvents.
• Depozitare: When not in use, always replace the protective cap over the measurement pins to prevent damage and injury. Store the device in a cool, dry place, away from direct sunlight and extreme temperatures.
• Înlocuire baterie: Replace batteries promptly when the low-battery indicator appears on the display to ensure accurate readings and prevent battery leakage.
• Îngrijirea pinilor: Ensure the measurement pins are clean and free from debris for optimal contact with the material.

5. Depanare

6. Specificații

Figure 5: The ANENG GN602 Moisture Meter displayed with its packaging, showing key dimensions and battery type.

7. Garanție și asistență

ANENG provides lifetime service and technical support for the GN602 moisture meter. For any inquiries, troubleshooting assistance, or warranty claims, please contact ANENG customer service through their official channels.

Vă rugăm să păstrați bonul fiscal pentru garanție.