ErGear Dual Monitor Desk Mount EGCM13B Instruction Manual

Introducere

Thank you for choosing the ErGear Dual Monitor Desk Mount. This manual provides detailed instructions for the safe and efficient installation, operation, and maintenance of your new monitor mount. Please read this manual thoroughly before installation and keep it for future reference.

Informații importante privind siguranța

Please ensure all instructions are read and understood before assembly and use. If you have any questions, please contact customer service. Failure to follow these instructions may result in property damage, serious injury, or death.

Verify that your monitor's weight and VESA pattern are within the specified limits.
Do not exceed the maximum load capacity of 26.5 lbs per arm.
Ensure the mounting surface (desk) is strong enough to support the combined weight of the mount and monitors.
Use only the provided hardware.
Păstrați piesele mici departe de copii.

Specificații

Model: EGCM13B
Compatibilitate cu dimensiunea ecranului: 13 până la 34 inci
Weight Capacity (per arm): Până la 26.5 lbs
Compatibilitate VESA: 75x75 mm, 100x100 mm
Arm Span: 33 inci
Înălțimea stâlpului: 16.3 inci
Tip de mișcare: Tilt, Swivel, Rotation, Articulating
Unghi maxim de înclinare: 90 de grade
Material: Oțel aliat
Culoare: Negru
Tip de montare: Suport de masă (C-Cl)amp sau Inel de fixare)
C-Clamp Grosimea biroului: 0.39" - 3.15"
Grommet Mount Desk Thickness: 0.39" - 2.17"
Diametrul orificiului pentru inel de etanșare: 0.47" - 0.79"

Conținutul pachetului

Please check that all parts are included and undamaged. If any parts are missing or damaged, please contact customer service.

Stâlp principal cu suport de birouampBază cu inel de fixare
Brațe pentru monitor dublu
Plăci VESA (2x)
Elemente de montare (șuruburi, șaibe, unelte)
Cleme de gestionare a cablurilor
Manual de instructiuni

ErGear Dual Monitor Desk Mount components laid out — Image: All components of the ErGear Dual Monitor Desk Mount laid out, including the main pole, dual arms, VESA plates, and various hardware for assembly.

Configurare și instalare

1. Verificarea compatibilității biroului

Before installation, ensure your desk meets the following criteria:

Material: Recomandat pentru mese din lemn.
Partea inferioară: Preferably free of beams or panels that may interfere with installation.
C-Clamp Grosime: 0.39" - 3.15"
Grosimea suportului inelului de prindere: 0.39" - 2.17" (Hole Diameter: 0.47" - 0.79")

2. Monitor Compatibility Check

Each monitor must meet these conditions:

Dimensiunea ecranului: 13 până la 34 inci
Greutate: Până la 26.5 lbs
Orificii de montare VESA: 75x75 mm or 100x100 mm apart on the back of the monitor.

Diagram showing VESA hole patterns on the back of a monitor — Image: Illustration of VESA mounting hole patterns (75x75mm and 100x100mm) on the back of a monitor, indicating where the mount attaches. It also shows how to remove a monitor's original stand.

3. Assemble the Pole with Clamp Sprijin

Choose either C-Clamp or Grommet installation based on your desk type.

Video: Demonstrates the installation process of the dual monitor desk mount, including assembling the pole with clamp support for both grommet and C-clamp methods. This video is provided by the seller.

Diagramă care prezintă C-Clamp și opțiuni de montare cu inele de etanșare — Image: Visual guide illustrating the two available mounting options: C-Clamp for desk edges and Grommet mount for desks with existing holes. Includes dimensions for compatible desk thickness and hole diameter.

Follow the detailed steps in the provided video and diagrams to securely attach the main pole to your desk using either the C-Clamp or Grommet method. Ensure all screws are tightened appropriately for stability.

4. Assemble the Arm and Pole Wire Clips

Attach the monitor arms to the main pole. Loosen the screw on the pipe clamp before installing the arm, then tighten it securely. Ensure the VESA plate side of the arm faces upwards. Install the cable management clips along the arms and pole.

5. Assemble VESA Plate and Monitor

Attach the VESA plate to the back of your monitor using the appropriate screws and washers. Ensure it is securely fastened.

6. Install the Monitor to the Swivel Arm

Carefully slide the monitor (with the attached VESA plate) onto the swivel arm. Secure it by tightening the locking screw. Adjust the screw with the Allen key to adjust the height of the VESA panel as needed (clockwise to lower, counter-clockwise to raise).

Image showing two monitors mounted on the ErGear Dual Monitor Desk Mount — Image: Two monitors securely mounted on the ErGear Dual Monitor Desk Mount, demonstrating a clean and organized workspace.

Operare și reglaje

The ErGear Dual Monitor Desk Mount offers versatile adjustments for optimal viewconfort:

Reglarea înălțimii: Slăbiți clamp on the main pole to slide the arms up or down to your desired height. Re-tighten the clamp în siguranță.
Înclinare: Adjust the monitor's vertical angle by tilting it +/-45 degrees to reduce glare and eye strain.
pivotare: Rotate the monitor horizontally +/-90 degrees for easy screen sharing or viewdin diferite unghiuri.
Rotaţie: Rotiți monitorul cu 360 de grade pentru a comuta între orientarea peisaj și portret.
Arm Extension/Retraction: The articulating arms allow you to extend or retract your monitors closer or further from you. Adjust the tension screws on the arm joints as needed to hold the desired position.

Diagramă care prezintă reglajele de înclinare, pivotare și rotație — Image: Visual representation of the monitor's flexible adjustments, including +/-45° tilt, +/-90° swivel, and 360° rotation, allowing for ergonomic positioning.

Întreţinere

Verificați periodic toate șuruburile și conexiunile pentru a vă asigura că rămân strânse și fixate.
Curățați suportul cu o lavetă moale,amp pânză. Evitați curățarea abrazivă.
Do not disassemble the mount unless instructed to do so.

Depanare

Monitoarele nu sunt la nivel: Ensure the VESA plates are correctly aligned and tightened. Adjust the small bolts on the tilt head to fine-tune alignment.
Monitors sag or do not hold position: Tighten the tension screws on the arm joints. Refer to the assembly instructions for specific locations.
Montura pare instabilă: Double-check that the C-Clamp or Grommet mount is securely fastened to the desk and all screws are fully tightened. Ensure your desk meets the thickness requirements.

Garanție și suport

For warranty information or technical support, please refer to the product packaging or contact ErGear customer service directly. Keep your purchase receipt as proof of purchase.

ErGear EGCM13B