Introducere
The Klein Tools 935DAF Digital Angle Finder is designed for precise measurements of inside and outside angles, lengths, and for calculating miter saw angles. It provides an accuracy of +/-0.2 degrees, assisting in achieving precise miter joints. Its compact design and clear display make it suitable for various professional and DIY applications.
Caracteristici cheie
- Funcționalitate versatilă 3 în 1: Measures inside and outside angles, lengths, and calculates miter saw cut angles.
- Miter Saw Protractor: Facilitates calculation of optimal saw blade angles for accurate miter joints.
- Machined Ruler Edges: Ensures accurate measurements with a precision of +/- 0.2 degrees.
- Display LED luminos: White LED display offers clear visibility in various lighting conditions.
- Construcție durabilă: Features a rust-resistant metallic ruler with deeply etched markings for longevity and clear readings.
- Design compact: Easy to store and carry, powered by a single AAA battery (included).
Înființat
1. Instalarea bateriei
The Klein Tools 935DAF requires one AAA battery, which is included. To install or replace the battery:
- Locate the battery compartment cover on the back of the digital display unit.
- Deschide capacul.
- Introduceți o baterie AAA, asigurându-vă că polaritatea este corectă (+/-).
- Închideți bine capacul compartimentului bateriei.
Image: The digital angle finder highlighting its bright LED display, wide locking knob, and indicating it is powered by a single AAA battery.
2. Powering On/Off and Zeroing
- Pornire/Oprire: Apăsați și mențineți apăsat butonul de pornire (⏻) for approximately 2 seconds to turn the device on or off.
- Resetare la zero: A short press of the power button (⏻) will reset the angle measurement to zero. Ensure the rulers are in the desired starting position before zeroing.
Instrucțiuni de operare
1. Measuring Angles
The digital angle finder can measure both inside and outside angles up to 360 degrees.
- Loosen the locking knob to allow the rulers to move freely.
- Position the rulers against the surfaces of the angle you wish to measure.
- Once positioned, tighten the locking knob to secure the angle.
- Read the angle measurement directly from the digital LED display.
Image: The digital angle finder positioned to measure a 90-degree angle on a wooden structure, displaying "90.0" on its screen.
Image: A user wearing work gloves uses the digital angle finder to measure and mark an angle on a piece of wood with a yellow pencil.
2. Miter Saw Angle Calculation
The 935DAF can assist in setting miter saw angles for precise cuts.
- Measure the desired angle of your joint using the angle finder.
- Apăsați tasta MTR DEG button. The display will show the calculated miter saw setting.
- Adjust your miter saw to this displayed angle for accurate miter cuts.
Image: The digital angle finder displaying "45.0" degrees, with the "MTR DEG" button visible, indicating its use for miter saw angle calculations.
3. Holding a Measurement
To hold the current measurement on the display, press the ȚINE button. Press it again to release and resume live measurement.
Întreţinere
Curatenie
Wipe the device with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these may damage the display or metallic surfaces.
Înlocuirea bateriei
Replace the AAA battery when the display becomes dim or the device fails to power on. Refer to the "Battery Installation" section under Setup for instructions.
Depozitare
Store the angle finder in a dry environment. Its compact design allows for easy storage in toolboxes or pockets.
Image: The digital angle finder being placed into a side pocket of a Klein Tools backpack, demonstrating its compact and portable design for easy storage.
Depanare
- Dispozitivul nu pornește:
- Ensure the AAA battery is correctly installed with proper polarity.
- Înlocuiți bateria cu una nouă.
- Confirm the power button is pressed and held for approximately 2 seconds.
- Citiri inexacte:
- Ensure the rulers are clean and free from debris that might obstruct proper contact with surfaces.
- Perform a zero reset by briefly pressing the power button when the rulers are closed or at a known zero position.
- Verify the locking knob is tightened to prevent movement during measurement.
- Afișajul este slab sau pâlpâie:
- Înlocuiți bateria AAA.
Specificații
| Producător | Klein Tools |
| Numărul piesei | 935DAF |
| Greutatea articolului | 6.9 uncii |
| Dimensiunile produsului | 8.55 x 1.38 x 0.74 inci |
| Numărul de model al articolului | 935DAF |
| baterii | Este necesară 1 baterie AAA (inclusă) |
| Material | Plastic ABS, Oțel inoxidabil |
| Sursa de alimentare | Alimentat cu baterie |
| Componente incluse | Găsitorul de unghi digital |
| Tipul celulei bateriei | Alcalin |
Informații despre garanție
For detailed warranty information, please refer to the attached warranty document provided with your product packaging. This document outlines the terms and conditions of the manufacturer's warranty.
Sprijin
For further assistance, technical support, or to inquire about replacement parts, please visit the official Klein Tools website-ul lor sau contactați departamentul lor de servicii pentru clienți. Puteți găsi mai multe informații și produse la Klein Tools Store on Amazon.
