FallTech FT Iron Worker Body Harness User Manual

Introducere

This manual provides essential information for the proper use, care, and maintenance of the FallTech FT Iron Worker Body Harness. This harness is designed for fall protection in various industrial and construction environments, specifically tailored for ironwork. Adherence to these instructions is crucial for user safety and product longevity. Always inspect the harness before each use.

Informații de siguranță

AVERTISMENT: Nerespectarea acestor instrucțiuni poate duce la vătămări corporale grave sau deces.

• Always inspect the harness for damage, wear, or defects before each use.
• Ensure all buckles and adjusters are securely fastened and properly adjusted.
• The harness must be used as part of a complete personal fall arrest system.
• Nu modificați hamul în niciun fel.
• Consult a qualified person for training on proper fall protection procedures.
• Maximum weight capacity for this harness is 425 lbs (including tools and clothing).

Componente terminateview

The FallTech FT Iron Worker Body Harness features several key components designed for comfort and safety.

Figura 1: Complet View of the FallTech FT Iron Worker Body Harness. This image displays the complete harness, highlighting its various straps, buckles, and D-rings from a side perspective.

Figura 2: Față View of the FallTech FT Iron Worker Body Harness. This image shows the front of the harness, including the chest strap, shoulder padding, and waist belt with quick-connect buckles.

Figura 3: Spate View of the FallTech FT Iron Worker Body Harness. This image illustrates the back of the harness, featuring the dorsal D-ring, shoulder straps, and back padding.

• Inel D dorsal: Located on the back, used as the primary attachment point for fall arrest.
• Inele D laterale: Located on the hips, used for work positioning or restraint.
• Curele de umăr: Adjustable straps that go over the shoulders, often padded for comfort.
• Curea de piept: Secures the shoulder straps across the chest, typically with a quick-connect buckle.
• Curele pentru picioare: Adjustable straps that go around the legs, usually with quick-connect buckles.
• Centura de talie: Provides support and attachment points for tools, with a belt buckle.
• Torso Adjusters: Mechanisms for adjusting the fit of the harness vertically.

Setup and Donning

Follow these steps to properly don and adjust your FallTech FT Iron Worker Body Harness:

1. Inspectați cablajul: Before each use, visually inspect the entire harness for cuts, fraying, broken stitches, heat damage, chemical damage, or any other signs of wear or damage. Ensure all buckles and D-rings are free of deformation or corrosion.
2. Hold by Dorsal D-Ring: Hold the harness by the dorsal D-ring (back D-ring) to allow the straps to fall into place.
3. Bretele de umăr: Slip the shoulder straps over your shoulders, as if putting on a vest. Ensure the dorsal D-ring is centered on your back, between your shoulder blades.
4. Conectați curelele pentru picioare: Bring the leg straps between your legs and connect them to the corresponding buckles on the waist belt or main harness body. Ensure the straps are not twisted.
5. Conectați cureaua de piept: Fasten the chest strap across your chest. Adjust its position so it is approximately mid-chest level.
6. Adjust Leg Straps: Tighten the leg straps so they are snug but allow for full range of motion. You should be able to slide your flat hand between the strap and your leg.
7. Ajustați bretelele de umăr: Pull the shoulder strap adjusters to remove any slack. The harness should fit snugly without restricting movement.
8. Adjust Torso/Waist Belt: Adjust the torso straps and waist belt to ensure a snug fit around your waist and hips. The waist belt should sit comfortably and securely.
9. Verificare finală: Perform a final visual check to ensure all straps are flat, not twisted, and all buckles are securely fastened. The harness should fit snugly, allowing for comfortable movement without excessive slack.

Operating and Use

The FallTech FT Iron Worker Body Harness is designed for fall arrest, work positioning, and restraint applications. Always connect to an approved anchorage point and compatible connecting device.

• Oprirea căderii: Connect a compatible lanyard or self-retracting lifeline to the dorsal D-ring. Ensure the anchorage point is capable of supporting 5,000 lbs (22.2 kN) per worker or meets OSHA/ANSI requirements.
• Pozitionare in munca: Use the side D-rings for work positioning. These are designed to support a worker in a suspended position, allowing hands-free operation. Always use a separate fall arrest system when using work positioning.
• Reţinere: The side D-rings can also be used for restraint, preventing a worker from reaching a fall hazard.
• Atașament sculă: The waist belt is designed to accommodate tool bags and other accessories. Ensure that the combined weight of tools and the user does not exceed the harness's maximum weight capacity.
• Post-Fall Procedure: In the event of a fall, immediately remove the harness from service. Do not use it again. The harness must be inspected by a competent person or destroyed. Seek medical attention if necessary.

Întreţinere

Proper maintenance extends the life of your harness and ensures its continued safety.

Curatenie

• Doar spălare manuală.
• Use a mild soap or detergent and lukewarm water.
• Scrub the harness with a stiff brush to remove dirt and grime.
• Clătiți bine cu apă curată până când toate reziduurile de săpun sunt îndepărtate.
• Hang to air dry in a clean, shaded area away from direct sunlight, heat, or open flame. Do not machine wash or dry.

Inspecţie

• Înainte de fiecare utilizare: Perform a visual inspection as described in the

  Documente conexe - 8144QCSM

  	Ghid de mărimi pentru hamurile de protecție împotriva căderii | FallTech Găsește potrivirea perfectă pentru hamul tău de protecție împotriva căderii cu ajutorul ghidului complet de mărimi FallTech. Află cum să măsori pieptul, talia și coapsele pentru siguranță și confort optime.
  	Manual de instrucțiuni pentru ham complet FallTech - MFBH04 Manual de instrucțiuni complet pentru utilizatorul hamului complet FallTech (model MFBH04). Acoperă avertismente de siguranță, descrierea, aplicarea, cerințele de sistem, instalarea, utilizarea, întreținerea, inspecția și definițiile pentru protecția împotriva căderii.
  	FallTech 7275 Adjustable Tripod: Installation, Operation, and Maintenance Manual User's instruction manual for the FallTech 7275 Adjustable Tripod, detailing installation, operation, maintenance, and safety guidelines for fall arrest, work positioning, and rescue applications.
  	Manual de utilizare și ghid de instalare pentru atașamentul sculei de contracție la rece FallTech This user manual provides essential safety information, application details, installation procedures, maintenance guidelines, and specifications for FallTech Cold Shrink Tool Attachments. Designed for dropped object prevention, these attachments are compatible with FallTech tool tethers and anchors, ensuring secure tool tethering for various hand and power tools. Includes models 5410A5, 5411A5, and 5412A5, meeting ANSI/ISEA 121-2018 standards.
  	Declarație de conformitate și raport de testare pentru șnur de siguranță reglabil FallTech Declarație de conformitate și raport de testare detaliat pentru șnurul de siguranță reglabil FallTech 8209, care confirmă conformitatea cu standardele ANSI Z359.3-2019 și ANSI/ISEA 125-2014.
  	FallTech Wood Frame Structure Anchors User Instruction Manual FallTech's User Instruction Manual for Wood Frame Structure Anchors provides essential guidance on the safe installation, operation, and maintenance of their Type A, B, and C anchors. Compliant with ANSI Z359 and OSHA standards, this manual is crucial for fall protection and restraint systems on wood-framed structures.