1. Introducere
1.1 Produs terminatview
The Sensor Switch SPODM-2P-RD nLight SwitchPod Control is a 2-button, low voltage (12/24-Vdc) wall-mount switch designed for nLight lighting control systems. This device provides manual ON/OFF control for connected lighting or other loads within an nLight network.
1.2 Caracteristici cheie
- nLight SwitchPod Switch
- Wall-Mount design
- 2-Button configuration (ON/OFF for two independent circuits or functions)
- Vol. Scăzuttage operation (12/24-Vdc)
- Finisaj roșu
1.3 Conținutul pachetului
- 1 x SPODM-2P-RD nLight SwitchPod Control
- Șuruburi de montare
- Ghid de instalare (acest manual)
2. Informații de siguranță
Please read all instructions carefully before installation and operation. Failure to follow these instructions may result in property damage, injury, or death.
- AVERTIZARE: To avoid fire, shock, or death, turn off power at the circuit breaker or fuse box and test that the power is off before wiring.
- Acest dispozitiv este conceput pentru volum redustage (12/24-Vdc) applications only. Do not connect to line voltage (120V/240V CA).
- Instalarea trebuie efectuată de către un electrician calificat, în conformitate cu toate codurile electrice locale și naționale.
- Nu instalați dacă produsul pare deteriorat.
- Nu modificați dispozitivul în niciun fel.
3. Configurare și instalare
3.1 Instrumente necesare
- Șurubelniță (Phillips și/sau cu cap plat)
- Dispozitive de dezimbrare
- Bandă izolatoare (opțional)
3.2 Instrucțiuni de cablare
The SPODM-2P-RD uses screw terminals for connection. Ensure all connections are secure.
Figura 3.2.1: lateral view of the SPODM-2P-RD with wiring label. This image shows the product's side profile, highlighting the label with detailed wiring instructions and specifications.
Figura 3.2.2: Spate view of the SPODM-2P-RD. This image illustrates the rear of the switch, revealing the screw terminals where low voltage wires are connected for power and control signals.
- Opriți alimentarea: Before beginning any wiring, ensure power to the circuit is turned off at the circuit breaker. Verify with a voltage tester.
- Identificați firele:
- WHT (White): Manual ON Input
- BLU (Blue) stripe: Right button output
- BLK (Black) stripe: Left button output
- RED (Red): Power (12/24-Vdc)
- YLW (Yellow): Comun
- Conectează firele: Connect the corresponding low voltage wires from your nLight system to the screw terminals on the SPODM-2P-RD. Ensure wires are stripped to the appropriate length and securely fastened under the screw terminals.
- Comutator de montare: Carefully push the wired switch into the wall box. Secure it using the provided mounting screws.
- Instalați placa de perete: Attach the decorative wallplate (not included) over the switch.
- Restabiliți puterea: Reporniți alimentarea la întrerupător.
4. Funcționare
4.1 Funcționalitate de bază
The SPODM-2P-RD features two independent push-buttons, each controlling an ON/OFF function within the nLight system. The control method is touch-based, responding to physical presses of the buttons.
Figura 4.1.1: Față view of the SPODM-2P-RD. This image displays the red faceplate with two sets of "ON" and "OFF" buttons, indicating its dual-channel control capability.
- Press the top "ON" button to activate the function associated with the upper control.
- Press the top "OFF" button to deactivate the function associated with the upper control.
- Press the bottom "ON" button to activate the function associated with the lower control.
- Press the bottom "OFF" button to deactivate the function associated with the lower control.
The specific actions triggered by these buttons are configured within the nLight system and may vary based on your installation.
5. Întreținere
The SPODM-2P-RD nLight SwitchPod Control requires minimal maintenance.
- curatenie: To clean the surface of the switch, use a soft, damp Nu utilizați produse de curățare abrazive, solvenți sau substanțe chimice dure, deoarece acestea pot deteriora finisajul sau componentele interne.
- Fără piese reparabile de utilizator: There are no user-serviceable parts inside this device. Do not attempt to open or repair the unit. Refer all servicing to qualified personnel.
6. Depanare
If you experience issues with your SPODM-2P-RD, refer to the following common troubleshooting steps:
| Problemă | Cauza posibila | Soluţie |
|---|---|---|
| Comutatorul nu răspunde. | Fără alimentare la dispozitiv. Cablare incorectă. nLight system issue. | Verify power is supplied to the nLight system and the switch. Check wiring connections against the diagram in Section 3.2. Consult your nLight system's documentation or administrator. |
| Buttons feel loose or stuck. | Physical damage or debris. | Ensure no foreign objects are obstructing the buttons. If physically damaged, the unit may need replacement. |
| Incorrect function when button is pressed. | Incorrect nLight system configuration. | Verify the nLight system programming for the switch's address and button assignments. |
If the problem persists after attempting these solutions, contact Sensor Switch technical support or a qualified electrician.
7. Specificatii tehnice
| Atribut | Caietul de sarcini |
|---|---|
| Numărul de model | SPODM-2P-RD |
| Marca | Comutator senzor |
| Modul de operare | Automat |
| Vol. De operaretage | 12/24 volți CC |
| Tip de contact | Deschis normal |
| Tip conector | Terminale cu șuruburi |
| Tipul circuitului | 2 sensuri |
| Tip actuator | Buton de apăsare |
| Material de contact | Metal |
| Evaluarea internațională de protecție | IP54 |
| Numărul de poziții | 2 |
| Metoda de control | Atingere |
| Culoare | Roşu |
| Dimensiuni (L x l x H) | 4 x 2.5 x 1.75 inci |
| Greutatea articolului | 7.4 uncii |
| Certificari | CE, ETL, REACH, RoHS, WEEE, cULus |
8. Garanție și asistență
This product is covered by the manufacturer's standard warranty. For specific warranty terms and conditions, please refer to the documentation provided with your purchase or visit the official Sensor Switch website-ul.
8.1 Suport tehnic
For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact Sensor Switch customer support. Contact information can typically be found on the manufacturer's webamplasamentul sau ambalajul produsului.
Nota: The input data does not provide specific contact details or warranty duration. Please refer to the manufacturer's official resources for the most accurate and up-to-date information.
