Introducere
This manual provides essential instructions for the safe and efficient operation, maintenance, and troubleshooting of your Truper ENNE-160 16 Gauge Pneumatic Stapler. Please read this manual thoroughly before using the tool to ensure proper handling and to prevent injury or damage.
Figure 1: Truper ENNE-160 16 Gauge Pneumatic Stapler, side view.
Informații de siguranță
Respectați întotdeauna măsurile de siguranță de bază atunci când utilizați scule electrice pentru a reduce riscul de incendiu, electrocutare și vătămare corporală. Păstrați acest manual pentru referințe ulterioare.
- Purtați protecție pentru ochi: Purtați întotdeauna ochelari de protecție sau ochelari de protecție pentru a vă proteja împotriva resturilor care zboară.
- Purtați protecție auditivă: Prolonged exposure to noise from pneumatic tools can cause hearing damage.
- Deconectați alimentarea cu aer: Always disconnect the air supply before making adjustments, clearing jams, or performing maintenance.
- Păstrați zona de lucru liberă: Asigurați-vă că zona dumneavoastră de lucru este bine iluminată și lipsită de dezordine.
- Securizarea piesei de lucru: Fixați întotdeauna materialul cu care lucrați pentru a-l împiedica să se miște.
- Nu arăta niciodată spre oameni: Never point the tool at yourself or others, even if it is not connected to an air supply.
- Use Correct Air Pressure: Operate the tool within the specified air pressure range (75-110 PSI).
- Inspectați unealta înainte de utilizare: Check for damaged parts, loose fasteners, or any other condition that may affect safe operation.
Caracteristicile produsului
The Truper ENNE-160 Pneumatic Stapler is designed for efficiency and user comfort. Key features include:
- Carcasa din aluminiu: Durable and lightweight construction for extended use.
- Mâner ergonomic: Designed for operator comfort and reduced fatigue.
- Sistem de eliberare rapidă: Facilitates easy clearing of jammed staples.
- Adjustable Depth Control: Allows precise control over staple depth.
- Metallic Contact Safety: Ensures staples are only fired when the tool is pressed against the workpiece.
- 360° Rotatable Air Exhaust Valve: Directs exhaust air away from the operator for improved comfort.
- Compatibilitate cu capse: Uses staples from 3/4" to 2" in length.
- Presiune de lucru: Operates efficiently between 75 and 110 PSI.
- Capacitatea cartusului: Holds up to 100 staples.
Figure 2: Key features and components of the Truper ENNE-160 Pneumatic Stapler.
Specificații
| Atribut | Valoare |
|---|---|
| Numărul de model | ENNE-160 |
| Ecartament capse | 16 Gauge |
| Material | Aluminiu |
| Presiune de lucru | 75 - 110 PSI (517 - 758 kPa) |
| Staple Lengths | 3/4", 1", 1 1/4", 1 1/2", 1 3/4", 2" |
| Capacitate cartuș | 100 de capse |
| Consumul de aer | 8.9 CFM @ 90 PSI (252 L/min @ 620 kPa) |
| Dimensiunile produsului | 11 x 36 x 31 cm (aproximativ 4.3 x 14.2 x 12.2 inci) |
| Greutatea produsului | 3.6 kg (aproximativ 7.9 livre) |
Figure 3: Dimensions of the Truper ENNE-160 Pneumatic Stapler.
Înființat
- Conectați alimentarea cu aer:
- Ensure the air compressor is off and depressurized.
- Connect a 1/4" NPT quick-change connector to the air inlet of the stapler.
- Attach the air hose from your compressor to the stapler's connector.
- Set the air compressor pressure regulator to the recommended operating range of 75-110 PSI. Do not exceed 110 PSI.
- Încărcați capse:
- Disconnect the air supply before loading staples.
- Locate the staple magazine release latch, typically at the rear of the magazine.
- Pull the magazine open or slide it back.
- Insert a strip of 16 gauge staples (3/4" to 2" length) into the magazine with the points facing down.
- Închideți bine magazia până când se blochează.
- Adjust Depth Control:
- The stapler features an adjustable depth control mechanism.
- Rotate the depth adjustment knob or lever (refer to Figure 2 for location) to set the desired staple depth. Test on a scrap piece of material first.
Instrucțiuni de operare
- Pregătirea piesei de lucru: Ensure the material is clean, dry, and free of obstructions. Secure the workpiece if necessary.
- Connect Air: Reconnect the air supply to the stapler.
- Instrument de poziționare: Place the nose of the stapler firmly against the workpiece where you want to drive a staple. The metallic contact safety mechanism requires pressure against the surface to allow firing.
- Fire Staple: Squeeze the trigger to drive a staple. Release the trigger after each staple.
- Continuous Operation (if applicable): Some models allow for bump firing. If your model supports this, hold the trigger and bump the nose of the tool against the workpiece to drive staples rapidly. Always exercise caution with this mode.
- Eliminarea blocajelor: If a staple jam occurs, immediately disconnect the air supply. Use the quick-release system to open the magazine and carefully remove the jammed staple. Reconnect air only after the jam is cleared and the magazine is closed.
- Adjust Air Exhaust: The 360° rotatable air exhaust valve can be adjusted to direct exhaust air away from your face or the workpiece.
Întreţinere
Regular maintenance ensures the longevity and optimal performance of your pneumatic stapler. Always disconnect the air supply before performing any maintenance.
- Lubrifiere: Apply a few drops of pneumatic tool oil into the air inlet daily or before each use. This lubricates internal components. Do not use detergent oil or automotive oil.
- curatenie: Keep the tool clean and free of debris. Wipe down the exterior with a clean cloth. Periodically clean the magazine and nose area to prevent staple jams.
- filtru de aer: If your air compressor has an inline air filter, ensure it is regularly cleaned or replaced to prevent contaminants from entering the tool.
- Inspectați furtunurile și fitingurile: Regularly check air hoses and fittings for wear, leaks, or damage. Replace any damaged components immediately.
- Depozitare: Store the stapler in a dry, clean environment when not in use. Disconnect it from the air supply.
Depanare
| Problemă | Cauza posibila | Soluţie |
|---|---|---|
| Instrumentul nu trage | No air supply; Low air pressure; Safety contact not engaged; Jammed staples; Trigger mechanism fault. | Check air connection and compressor pressure; Ensure tool nose is firmly pressed against workpiece; Disconnect air and clear jam; Contact service if trigger fault. |
| Staples not driven fully | Low air pressure; Depth control set too shallow; Incorrect staple length for material. | Increase air pressure (within limits); Adjust depth control deeper; Use appropriate staple length. |
| Staples jam frequently | Damaged staples; Incorrect staple size; Dirty magazine; Worn driver blade. | Use new, correct staples; Clean magazine; Inspect and replace driver blade if worn. |
| Scurgeri de aer din unealtă | Loose fittings; Worn O-rings or seals. | Tighten fittings; Lubricate tool; If leaks persist, contact service for seal replacement. |
Garanție și suport
TRUPER products are manufactured to high-quality standards. For warranty information, service, or technical support, please refer to the warranty card included with your product or visit the official TRUPER webPăstrați bonul fiscal ca dovadă a achiziției pentru reclamații în garanție.
Producător: Truper SA de CV
