Manual de utilizare pentru pompă submersibilă Everbilt din aluminiu de 1/2 CP cu întrerupător conectat

Introducere

This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Everbilt 1/2 HP Submersible Aluminum Sump Pump. Please read all instructions carefully before use to ensure proper function and to prevent injury or damage.

Informații de siguranță

AVERTIZARE: Deconectați întotdeauna alimentarea cu energie electrică înainte de a efectua orice operațiune de service sau întreținere a pompei.

PERICOL: Risc de electrocutare. Această pompă este furnizată cu un conductor de împământare și un ștecher de atașare de tip împământare. Pentru a reduce riscul de electrocutare, asigurați-vă că acesta este conectat numai la o priză de tip împământare cu împământare.

• Nu folosiți pompa dacă cablul de alimentare sau ștecherul sunt deteriorate.
• Asigurați-vă că pompa este amplasată pe o suprafață stabilă și plană.
• Nu pompați lichide inflamabile sau corozive.
• Țineți copiii și animalele de companie departe de pompa în funcțiune.
• Purtați echipament individual de protecție (EIP) adecvat atunci când manipulați pompa.
• This pump is designed for clear water only.

Produs terminatview

The Everbilt 1/2 HP Submersible Sump Pump is designed for efficient water removal from sump basins. It features an aluminum motor housing for effective cooling and a tethered float switch for automatic operation.

Figura 1: Everbilt 1/2 HP Submersible Aluminum Sump Pump. This image shows the black pump unit with its tethered float switch, power cord, and 1-1/2 inch FNPT discharge port. The Everbilt logo is visible on the side of the pump body.

Caracteristici cheie:

• Aluminum motor housing for efficient motor cooling.
• Continuous duty, efficient 115-Volt PSC motor for lower carbon footprint; higher efficiency using less energy to operate.
• 8.25 ft. cord length.
• Submersible for quiet operation.
• 1-1/2 in. FNPT discharge.
• Semi-open thermoplastic impeller passes 3/8 in. solids.
• Protecție la suprasarcină termică.

Configurare și instalare

1. Sump Basin Preparare: Ensure your sump basin has a minimum diameter of 18 inches to accommodate the tethered float switch. Clean the basin of any debris or obstructions.
2. Plasare: Place the pump on a solid, level surface at the bottom of the sump basin. Ensure the pump is stable and will not tip over during operation.
3. Conectarea conductei de refulare: Connect a 1-1/2 inch FNPT (Female National Pipe Thread) discharge pipe to the pump's outlet. It is recommended to use a check valve in the discharge line to prevent water from flowing back into the sump basin when the pump turns off.
4. Reglarea comutatorului cu flotor: The tethered float switch controls the pump's on/off cycles. Adjust the tether length to set the desired "on" and "off" water levels. Ensure the float can move freely without obstruction within the sump basin. The switch-on height is approximately 11.81 inches and switch-off height is approximately 3.94 inches, but can be adjusted by tether length.
5. Conexiune de alimentare: Plug the pump's 8.25 ft. power cord into a properly grounded 115-Volt AC outlet. Ensure the outlet is protected by a Ground Fault Circuit Interrupter (GFCI) for added safety.
6. Funcționare de testare: Fill the sump basin with water to activate the float switch and ensure the pump turns on and discharges water correctly. Allow the water level to drop to verify the pump turns off automatically.

Instrucțiuni de operare

The Everbilt 1/2 HP Submersible Sump Pump operates automatically via its tethered float switch. Once properly installed and connected to power, the pump will activate when the water level rises to the "on" point and deactivate when the water level drops to the "off" point.

• Funcționare automată: The pump is designed for continuous duty and will cycle on and off as needed based on the water level in the sump basin.
• Suprareglare manuală (dacă este cazul): While primarily automatic, some installations may allow for manual operation by lifting the float switch. Refer to your specific setup for manual control options.
• Monitorizare: Verificați periodic baia de ulei basin and pump operation, especially during heavy rainfall, to ensure it is functioning correctly.

Întreţinere

Regular maintenance ensures the longevity and reliable operation of your sump pump.

1. Deconectați alimentarea: Always disconnect the pump from the power source before performing any maintenance.
2. Curățați baia de evacuare Basin: Periodically remove any debris, dirt, or sediment from the sump basin that could interfere with pump operation or float switch movement.
3. Inspect Impeller: Check the pump's impeller for any clogs or damage. The semi-open thermoplastic impeller is designed to pass 3/8 inch solids, but larger debris can cause issues.
4. Verificați comutatorul cu flotor: Ensure the tethered float switch moves freely and is not obstructed by wires, pipes, or debris.
5. Verificați cablul de alimentare: Examine the power cord for any signs of wear, cuts, or damage. Replace if necessary.
6. Iernare (dacă este cazul): Dacă pompa se află într-o zonă cu temperaturi de îngheț și nu va fi utilizată, scoateți-o din priză.asin, clean it, and store it in a dry, warm place.

Depanare

If problems persist after attempting these solutions, please contact Everbilt customer support.

Specificații

Garanție și suport

For warranty information or technical support, please contact Everbilt customer service. Keep your purchase receipt as proof of purchase for any warranty claims.

Pentru asistență suplimentară, puteți vizita Everbilt brand page on Amazon or consult the retailer where the product was purchased.