1. Introducere
This manual provides essential information for the safe and effective operation of your Tektronix Digital Storage Oscilloscope, Model B07GCZSDRJ. This device is designed for precise measurement and analysis of electronic signals. Please read this manual thoroughly before using the instrument to ensure proper functionality and to prevent damage or injury.
2. Informații de siguranță
Always observe the following safety precautions to prevent injury and avoid damage to this product or any products connected to it.
- Utilizați produsul numai așa cum este specificat.
- Nu utilizați produsul dacă este deteriorat.
- Perform initial safety checks before connecting to power.
- Adresați service-ul personalului calificat.
- Asigurați o ventilație adecvată pentru a preveni supraîncălzirea.
- Nu operați în zone umede sau damp conditii.
3. Configurare
Follow these steps to set up your oscilloscope for the first time:
- Unpack the Instrument: Carefully remove the oscilloscope and all accessories from the packaging. Inspect for any visible damage.
- Conectare alimentare: Connect the provided power cord to the AC input on the rear panel of the oscilloscope, then plug it into a grounded electrical outlet.
- Pornire: Press the power button, usually located on the front panel. The display should illuminate.
- Compensarea sondei: If using probes, connect a probe to Channel 1 and the probe compensation output. Adjust the probe compensation until a flat-top square wave is displayed.
This image serves as a placeholder and indicates that a specific product image is not available for display. It typically shows text like 'No image available' with a generic Amazon smile logo.
4. Instrucțiuni de utilizare
This section covers basic operation of the oscilloscope.
- Controale verticale: Use the VOLTS/DIV knob to adjust the vertical scale (voltage per division) and the position knob to move the waveform vertically.
- Controale orizontale: Use the SEC/DIV knob to adjust the horizontal scale (time per division) and the position knob to move the waveform horizontally.
- Sistem de declanșare: The trigger controls stabilize repetitive waveforms. Adjust the trigger level and mode (e.g., Edge, Pulse) to capture the desired part of the signal.
- Functii de masurare: Access built-in measurement functions (e.g., Vpp, RMS, Frequency) via the 'Measure' or 'Menu' buttons.
5. Întreținere
Proper maintenance ensures the longevity and accuracy of your oscilloscope.
- curatenie: Curăţaţi exteriorul instrumentului cu un material moale, damp cloth. Do not use abrasive cleaners or solvents. Ensure the instrument is powered off and unplugged before cleaning.
- Calibrare: Regular calibration by qualified service personnel is recommended to maintain measurement accuracy. Refer to the service manual for calibration procedures.
- Depozitare: When not in use, store the oscilloscope in a clean, dry environment, away from direct sunlight and extreme temperatures.
6. Depanare
Această secțiune oferă soluții pentru problemele comune pe care le-ați putea întâmpina.
| Problemă | Cauza posibila | Soluţie |
|---|---|---|
| Fără afișaj după pornire | Power cord not connected; Power outlet fault; Internal fuse blown | Check power cord connection; Test power outlet; Contact service for fuse replacement |
| Nu este afișată nicio formă de undă | Input signal too small; Probe not connected; Trigger settings incorrect | Increase VOLTS/DIV; Check probe connection; Adjust trigger level and mode |
| Waveform unstable or rolling | Trigger level incorrect; Trigger source not selected; Input signal noisy | Adjust trigger level; Select correct trigger source; Use averaging mode for noisy signals |
7. Specificații
Key technical specifications for the Tektronix Digital Storage Oscilloscope, Model B07GCZSDRJ.
| Caietul de sarcini | Valoare |
|---|---|
| ASIN | B07GCZSDRJ |
| Producător | Tektronix |
| Data primului disponibil | 11 august 2018 |
8. Garanție și asistență
Tektronix products are designed for reliability and performance. This product comes with a standard manufacturer's warranty. For specific warranty terms and conditions, please refer to the documentation included with your purchase or visit the official Tektronix website-ul.
For technical support, service, or to inquire about replacement parts, please contact Tektronix customer service. You can find contact information on the official Tektronix website-ul sau prin distribuitorul local.
Notă: Reparațiile sau modificările neautorizate pot anula garanția.
