Introducere
This manual provides detailed instructions for the safe and efficient operation, installation, and maintenance of your Igloo MWC8988 Bottom Loading Water Dispenser. Please read this manual thoroughly before using the appliance and retain it for future reference.
The Igloo MWC8988 is a freestanding water dispenser designed to provide cold, hot, and room temperature water. Its bottom-loading design eliminates the need for lifting heavy water bottles, concealing them neatly within the base of the unit. The dispenser features a compressor for efficient cooling and a heating element for hot water on demand.
Informații importante privind siguranța
To reduce the risk of injury or property damage, observe the following safety precautions:
- Always plug the dispenser into a grounded electrical outlet. Do not use extension cords.
- A se păstra dozatorul departe de lumina directă a soarelui și de surse de căldură.
- Ensure proper ventilation around the unit. Maintain at least 4 inches (10 cm) clearance from walls.
- Do not operate the dispenser without a water bottle installed.
- Supravegheați copiii când se află în apropierea dozatorului, în special când distribuiți apă caldă.
- Deconectați dozatorul de la priză înainte de curățare sau de efectuarea oricărei operațiuni de întreținere.
- Nu scufundați dozatorul, cablul sau ștecherul în apă sau alte lichide.
- Dacă cablul de alimentare este deteriorat, acesta trebuie înlocuit de producător, de agentul său de service sau de persoane calificate similar pentru a evita un pericol.
- Acest aparat este destinat să fie utilizat în aplicații casnice și similare, cum ar fi zonele de bucătărie pentru personal în magazine, birouri și alte medii de lucru; fermelor și de către clienți în hoteluri, moteluri și alte medii de tip rezidențial; medii tip pensiune; catering și aplicații similare non-retail.
Conținutul pachetului
La despachetare, vă rugăm să vă asigurați că toate articolele sunt prezente și nedeteriorate:
- Igloo MWC8988 Bottom Loading Water Dispenser
- Water Probe Assembly
- Manual de utilizare (acest document)
Produs terminatview
Familiarizați-vă cu componentele dozatorului de apă.

Figura 1: Faţă view of the Igloo MWC8988 water dispenser with the bottom compartment door open, revealing a water bottle and the water probe assembly. The top features dispensing buttons and indicator lights for cooling, heating, and power.

Figura 2: Latura view of the Igloo MWC8988 water dispenser highlighting key features such as bottom loading, freestanding design, compressor cooling, 420W heating power, and 100W cooling power.
Instrucțiuni de configurare
- Despachetați dozatorul: Carefully remove all packaging materials. Place the dispenser on a flat, level surface.
- Pozitionare: Ensure the dispenser is placed in a cool, dry location, away from direct sunlight and heat sources. Allow at least 4 inches (10 cm) of clearance from walls for proper ventilation.
- Instalați sticla de apă:
- Open the bottom compartment door of the dispenser.
- Remove the protective cap from a new 3 or 5-gallon water bottle.
- Insert the water probe assembly into the opening of the water bottle. Ensure the probe is fully inserted and the bottle is sealed.
- Glisați sticla de apă în compartimentul de jos.
- Închideți ușa compartimentului în siguranță.
- Amorsați sistemul: Before plugging in the unit, place a cup under each dispenser faucet (hot, cold, room temperature) and press the buttons until water flows steadily from each. This removes air from the lines.
- Conectare: Plug the dispenser into a grounded 120V AC electrical outlet.
- Activare încălzire/răcire: The cooling and heating functions will begin automatically. Allow approximately 15-30 minutes for the water to reach optimal cold and hot temperatures. The indicator lights on the front panel will show when the desired temperatures are reached.
Instrucțiuni de operare
Your Igloo MWC8988 dispenser offers three temperature options:
- Apa rece: Press the blue button to dispense chilled water.
- Apa la temperatura camerei: Press the green button to dispense water at ambient temperature.
- Apa calda: For safety, the hot water faucet typically has a child-safety lock. Simultaneously press the red button and slide the safety lock (if present) to dispense hot water. Exercise caution as hot water can cause burns.
When the water bottle is empty, the "Bottle Empty" indicator light will illuminate. Replace the bottle following the "Install Water Bottle" steps in the Setup section.
Întreţinere
Curățarea și întreținerea regulată asigură performanțe și igienă optime.
- Curatenie exterioara: Ștergeți suprafețele exterioare cu un material moale, damp pânză. Nu utilizați agenți de curățare abrazivi sau solvenți.
- Curățarea tăvii de scurgere: Tava de scurgere trebuie golită și curățată periodic pentru a preveni revărsarea și dezvoltarea bacteriilor. Scoateți tava, spălați-o cu apă și săpun delicat, clătiți bine și puneți-o la loc.
- Curățare internă (Detartrare):
- Deconectați dozatorul și scoateți sticla de apă.
- Drain all water from the hot and cold tanks using the drain plugs located at the back of the unit (refer to your specific model's diagram for exact location).
- Prepare a cleaning solution of 1 gallon (3.8 liters) of water mixed with 2 tablespoons of household bleach or a food-grade descaling solution.
- Pour the cleaning solution into the water reservoir (where the probe usually sits).
- Allow the solution to sit for 15-20 minutes.
- Drain the solution completely from both hot and cold water faucets and the drain plugs.
- Rinse the system thoroughly by filling the reservoir with clean water and draining it several times until no bleach odor remains.
- Replace the drain plugs, install a new water bottle, and plug in the dispenser.
Depanare
| Problemă | Cauza posibila | Soluţie |
|---|---|---|
| Fără distribuire de apă. | Water bottle empty or not properly installed. Air lock in the system. | Replace water bottle. Prime the system by pressing all dispense buttons until water flows. |
| Apa nu este suficient de rece/fierbinte. | Dispenser recently plugged in. Heating/cooling switch off. Poor ventilation. | Allow 15-30 minutes for temperatures to stabilize. Ensure heating/cooling switches (if present, usually at the back) are ON. Check for adequate clearance around the unit. |
| Scurgerea apei din unitate. | Water bottle cracked or improperly seated. Drain plug loose. | Check water bottle for cracks and ensure it's correctly installed. Tighten drain plugs at the back. If leaking persists, unplug and contact support. |
| Fără putere. | Dispenser unplugged. Power outlet not working. Circuit breaker tripped. | Ensure dispenser is securely plugged in. Test the outlet with another appliance. Reset the circuit breaker. |
Specificații
| Model: | MWC8988 |
| Marca: | IGLOO |
| Tip: | Distribuitor de apă cu încărcare inferioară |
| Dimensiuni (L x l x H): | 40.64 x 39.37 x 113.03 cm (16 x 15.5 x 44.5 țoli) |
| Greutate: | 17.69 kg (39 lbs) |
| Material: | Aluminium (internal components, exterior likely plastic/metal) |
| Putere de incalzire: | 420 wați |
| Putere de racire: | 100 wați |
| Tip de instalare: | Freestanding |
| Locație de acces: | Fund |
| UPC: | 058465801656 |
Garanție și suport
Specific warranty details and customer support contact information were not provided in the product data. For warranty claims or technical assistance, please refer to the documentation included with your purchase or visit the official Igloo website pentru cele mai actuale informații.





