1. Introducere
This manual provides comprehensive instructions for the GENIUS KILO TX2 JL remote control. Please read this manual carefully before using the device to ensure proper operation and to maximize its lifespan. Keep this manual for future reference.
2. Produs terminatview
The GENIUS KILO TX2 JL is a two-button remote control designed for gate and garage door opener systems. It operates on a frequency of 868.35 MHz, providing reliable communication with compatible receivers.
- Model: KILO TX2 JLC
- Frecvenţă: 868.35 MHz
- Butoane: 2
- Compatibilitate: Compatible with GENIUS 868 systems and various gate opener remote controls including CASALI JA332, CASALI JA332 Grey, GENIUS JA332, GENIUS JA332 GREY, POWERDOOR JA332, POWERDOOR JA332 GREY, and GENIUS JA332 ORANGE.
- Receptoare compatibile: JA335, 6100075, 6100146, 6100229, 6100230.
Figura 1: Față view of the GENIUS KILO TX2 JL remote control. This image displays the white remote with two distinct circular buttons and the 'GENIUS' brand name at the bottom.
Figura 2: Spate view of the GENIUS KILO TX2 JL remote control. This image shows the reverse side of the remote, featuring the model number '6100332 (KILO TX2 JLC)', '868 MHz', 'Made In IE', and the 'CE 0470' marking.
3. Configurare
3.1. Instalarea bateriei
The GENIUS KILO TX2 JL remote control requires one CR2 battery. The remote is typically supplied with a battery already installed. If replacement is needed, follow these steps:
- Locate the battery compartment on the remote control. This is usually secured by small screws or a clip.
- Deschideți cu grijă compartimentul folosind o șurubelniță mică, dacă este necesar.
- Scoateți vechea baterie CR2.
- Insert a new CR2 battery, ensuring the correct polarity (+ and -) is observed.
- Închideți bine compartimentul bateriei.
Nota: Aruncați bateriile uzate în mod responsabil, conform reglementărilor locale.
3.2. Programarea telecomenzii
Programming the GENIUS KILO TX2 JL remote control involves linking it to your specific gate or garage door opener receiver. The exact programming procedure can vary depending on the model of your receiver.
General steps often include:
- Accesați receptorul: Locate the programming button or switch on your gate or garage door opener's receiver unit. This unit is typically located near the motor.
- Activează modul de învățare: Press and release the programming button on the receiver. An indicator light (LED) on the receiver will usually illuminate or flash, indicating it is in learning mode.
- Transmit Code: Within a few seconds of activating learning mode, press and hold the desired button on your new GENIUS KILO TX2 JL remote control.
- Confirmare programare: The receiver's indicator light will typically change (e.g., flash rapidly, turn solid, or turn off) to confirm that the remote control has been successfully programmed.
- Funcționare de testare: After programming, test the remote control by pressing the programmed button to ensure it operates your gate or garage door correctly.
Important: Always refer to the instruction manual provided with your specific gate or garage door opener system for detailed and accurate programming instructions. If you are replacing an existing remote, some systems allow for cloning from an already programmed remote.
4. Instrucțiuni de utilizare
Once programmed, operating the GENIUS KILO TX2 JL remote control is straightforward:
- Deschidere/Închidere: Press the programmed button on the remote control once to activate your gate or garage door opener. Pressing it again will typically stop or reverse the operation, depending on your system's configuration.
- Gamă: The remote has a maximum range of 10 meters. Ensure you are within this range for reliable operation. Environmental factors and obstacles can affect the effective range.
5. Întreținere
5.1. Înlocuirea bateriei
If the remote control's range decreases significantly or the indicator light (if present) does not illuminate when a button is pressed, the battery may need replacement. Refer to Section 3.1 for battery installation instructions. Use only CR2 alkaline batteries.
5.2. Curatenie
Clean the remote control with a soft, dry cloth. Do not use abrasive cleaners, solvents, or immerse the device in water, as this can damage the internal components.
6. Depanare
| Problemă | Cauza posibila | Soluţie |
|---|---|---|
| Telecomanda nu funcționează. | Dead or low battery. Incorrect programming. Out of range. | Replace the battery (CR2). Re-program the remote control (refer to Section 3.2). Move closer to the receiver. |
| Raza de acțiune redusă. | Low battery. Interference from other devices. Obstructions. | Replace the battery. Check for sources of interference. Ensure a clear line of sight to the receiver if possible. |
| Gate/door opens intermittently. | Weak battery. Environmental factors. | Replace the battery. Ensure the remote is not exposed to extreme temperatures or moisture. |
If troubleshooting steps do not resolve the issue, contact your gate or garage door opener system installer or manufacturer for further assistance.
7. Specificații
| Caracteristică | Detaliu |
|---|---|
| Marca | Geniu |
| Numărul de model | KILO TX2 JLC |
| Frecvenţă | 868.35 MHz |
| Numărul de butoane | 2 |
| Tip baterie | 1 x CR2 (Alkaline) |
| Raza maximă | 10 metri |
| Tehnologia de conectivitate | Frecventa radio |
| Dispozitive compatibile | Genius 868 systems |
| Caracteristica specială | Universal compatibility with listed models |
8. Garanție și asistență
Warranty information for the GENIUS KILO TX2 JL remote control is typically provided by the retailer or manufacturer at the time of purchase. Please retain your proof of purchase for warranty claims.
For technical support, programming assistance beyond the general steps provided, or warranty inquiries, please contact the authorized Genius dealer or the customer support department of your gate or garage door opener system manufacturer.
