1. Produs terminatview
The Exmark 109-4180 is a genuine Exmark Toro factory part, a bi-directional 25 micron filter essential for maintaining the hydraulic system of compatible Exmark lawn and garden equipment. This filter is designed to capture fine particles, ensuring the longevity and optimal performance of your machinery's hydraulic components.
Figura 1: Față view of the Exmark 109-4180 Bi-Directional 25 Micron Filter, showing the Exmark Original Parts logo.
Caracteristici cheie:
- Genuine Exmark Toro Factory Part Number 109-4180.
- Replacement for Previous Part Numbers: 1-513211, 1-543811, 109-4180-S.
- Bi-directional 25 micron filtration for effective particle removal.
- Compatible with a wide range of Exmark models including: ARX440CKC24000, ARX440GKC24000, ARX481CKA30000, ARX541CKA30000, Staris E-Series, Explorer, Lazer AS, Lazer HP, Lazer Z, Lazer Z AC, Lazer Z AS, Lazer Z CT, Lazer Z HP, Lazer Z LC, Navigator, SAR481KA30, SAR481KA30CA, Staris S-Series, Turf Tracer S-Series, Vantage S-Series, Viking Hydro S-Series, Turf Ranger, Turf Tracer 1800, Turf Tracer HP, Turf Tracer Hydro, Turf Tracer Hydro ECS, Vantage, Viking Hydro, X-Series Hydro Turf Tracer, Turf Tracer X-Series, Vantage X-Series.
2. Instalare și configurare
Proper installation of the hydraulic filter is crucial for the optimal performance and longevity of your Exmark equipment. Always refer to your specific equipment's service manual for detailed, model-specific instructions and safety precautions before proceeding.
Pasi generali de instalare:
- Preparare: Ensure the equipment is turned off, cooled down, and on a level surface. Disconnect the battery if necessary. Prepare a drain pan for used hydraulic fluid.
- Localizați filtrul: Identify the existing hydraulic filter on your equipment.
- Eliminați filtrul vechi: Carefully unscrew the old filter. Be prepared for some fluid to drain. Dispose of the old filter and fluid according to local regulations.
- Pregătiți filtrul nou: Apply a thin film of clean hydraulic fluid to the new filter's gasket. This ensures a proper seal.
- Instalați filtrul nou: Screw the new Exmark 109-4180 filter onto the filter head by hand until the gasket makes contact. Then, tighten an additional 3/4 to 1 full turn, or as specified in your equipment's manual. Do not overtighten.
- Refill Hydraulic System: Top off the hydraulic fluid to the recommended level, if necessary, using the correct type of fluid specified by Exmark.
- Verificați dacă există scurgeri: Start the equipment and allow it to run for a few minutes. Check for any leaks around the new filter.
Figure 2: Diagram illustrating the general steps for hydraulic filter installation, including preparing the gasket and tightening the filter.
3. Principii de funcționare
The Exmark 109-4180 Bi-Directional 25 Micron Filter functions as a critical component in your equipment's hydraulic system. Its primary role is to remove contaminants from the hydraulic fluid, such as dirt, metal particles, and other debris, which can cause wear and damage to sensitive hydraulic components like pumps, motors, and valves.
Being bi-directional, this filter is designed to maintain its filtration efficiency regardless of the direction of fluid flow, which is common in hydraulic systems that experience fluctuating flow patterns. The 25-micron rating indicates that it can effectively capture particles 25 micrometers or larger, providing a good balance between filtration efficiency and flow restriction for the specified applications.
A clean hydraulic filter ensures that the hydraulic fluid remains pure, allowing the system to operate at peak efficiency, reduce friction, dissipate heat, and transmit power effectively. Regular replacement is key to preventing costly repairs and extending the lifespan of your hydraulic system.
4. Întreținere
Regular maintenance of your hydraulic filter is essential for the health of your Exmark equipment's hydraulic system. The 109-4180 filter is a consumable part that requires periodic replacement.
Program de înlocuire a filtrului:
Refer to your specific Exmark equipment's operator's manual for the recommended hydraulic filter replacement intervals. These intervals are typically based on operating hours or seasonal usage. Adhering to the recommended schedule helps prevent premature wear of hydraulic components and maintains system efficiency.
Semne ale unui filtru înfundat:
- Reduced hydraulic system performance (e.g., slower lift, steering issues).
- Increased operating temperature of hydraulic fluid.
- Unusual noises from hydraulic pump or components.
- Warning lights or indicators on the equipment dashboard (if applicable).
Eliminare:
Used hydraulic filters and fluid must be disposed of responsibly according to local environmental regulations. Many automotive or equipment service centers offer recycling programs for used oil and filters.
Figure 3: Exmark engine oil and filter kit, highlighting the importance of using genuine parts for maintenance.
Official Exmark Parts Video:
Video 1: An official video from Exmark Manufacturing showcasing genuine lawn and garden replacement parts, including filters, oils, and other maintenance items.
5. Depanare
If you experience issues with your hydraulic system after filter replacement or during normal operation, consider the following troubleshooting steps:
- Scurgeri de fluide: Check the filter's seal and tightness. Ensure the gasket was properly lubricated and the filter is not cross-threaded.
- Performanță redusă: If performance issues persist after filter replacement, the problem may lie elsewhere in the hydraulic system (e.g., pump, valves, fluid level, or other components).
- Filtru incorect: Verify that the correct filter (Exmark 109-4180 or equivalent) was installed. Using an incorrect filter can lead to poor filtration or flow issues.
- Contaminated Fluid: If the hydraulic fluid appears discolored or contains visible particles shortly after replacement, the system may have significant internal contamination or a severe component failure.
For complex hydraulic system issues, it is recommended to consult a qualified Exmark service technician or refer to your equipment's comprehensive service manual.
6. Specificații
Detailed specifications for the Exmark 109-4180 Bi-Directional 25 Micron Filter:
| Atribut | Valoare |
|---|---|
| Numărul de model al articolului | 109-4180 |
| Marca | Exmark |
| Gradul de produs | Piesa de schimb |
| Material | Plastic (likely referring to internal components or packaging, as the filter body is metal) |
| Dimensiuni produs (L x l x H) | 16 x 10 x 1 inci |
| Greutatea articolului | 9.6 uncii |
| Evaluare de filtrare | 25 microni |
| Service Type Compatibility | Exmark Lazer Z, Exmark Lazer Z AC, Exmark Lazer Z AS, Exmark Lazer Z CT, Exmark Lazer Z HP, Exmark Lazer Z LC, Exmark Navigator, Exmark Staris E-Series, Exmark Staris S-Series, Exmark Turf Ranger, Exmark Turf Tracer, Exmark Turf Tracer 1800, Exmark Turf Tracer ECS, Exmark Turf Tracer HP, Exmark Turf Tracer S-Series, Exmark Turf Tracer X-Series, Exmark Vantage, Exmark Vantage S-Series, Exmark Vantage X-Series, Exmark X-Series Hydro Turf Tracer, Toro Aerator 24, Toro Aerator 30, Toro Explorer, Toro Z-Spray 3624, Toro Z-Spray 4230, Toro Z-Spray 4630, Toro Z-Spray 5260, Toro Z-Spray 5260XL |
Note: Dimensions and weight are for the packaged product. The "Material: Plastic" specification might refer to internal filter media or packaging, as the filter housing is typically metal.
7. Garanție și asistență
Specific warranty information for the Exmark 109-4180 Bi-Directional 25 Micron Filter is typically provided at the point of purchase or within the documentation accompanying your Exmark equipment. As a genuine replacement part, it is generally covered under the standard Exmark parts warranty, which protects against defects in material and workmanship.
For detailed warranty terms, claims, or technical support, please contact Exmark customer service or an authorized Exmark dealer. You can find contact information and dealer locators on the official Exmark website:
Visit the Official Exmark Website-ul
When contacting support, please have your equipment model and serial number, as well as the filter part number (109-4180), ready to assist them in providing the best possible service.
