Produs terminatview
The Atlas AE803-2520 is a high-performance pistol-grip pneumatic insert tool designed for efficient installation of threaded inserts. This spin/spin tool operates at 600 RPM and is equipped with a 1/4-20 thread adapter kit, making it suitable for various industrial and assembly applications. Its robust design ensures durability and reliable performance.
Image: The Atlas AE803-2520 Pistol Spin/Spin Pneumatic Insert Tool, showing its ergonomic pistol grip and front spindle.
Informații importante privind siguranța
Always follow these safety precautions to prevent injury and damage to the tool.
- Citiți și înțelegeți toate instrucțiunile înainte de a utiliza unealta.
- Purtați echipament individual de protecție (EIP) adecvat, inclusiv protecție pentru ochi, protecție auditivă și mănuși.
- Ensure the air supply is disconnected before performing any maintenance, adjustments, or changing accessories.
- Maintain a secure grip on the tool during operation.
- Nu folosiți unealta dacă este deteriorată sau funcționează defectuos.
- Păstrați zona de lucru curată și bine iluminată. Zonele aglomerate sau întunecate provoacă accidente.
- Use only genuine Atlas replacement parts and accessories.
Componentele sculei
Familiarize yourself with the main components of your Atlas pneumatic insert tool:
- Mâner pentru pistol: Proiectat ergonomic pentru o manevrare confortabilă și sigură.
- Declanșator: Activates the tool's pneumatic motor.
- Admisie: Connection point for the compressed air supply.
- Spindle/Mandrel: The rotating part that engages with the threaded insert.
- Depth Adjustment Collar: Allows for precise control over the insert installation depth.
- Buton invers: Used to reverse the spindle rotation for removing the tool from the installed insert.
Image: The official Atlas Tools logo, indicating the brand of the pneumatic insert tool.
Instrucțiuni de configurare
- Conexiune de alimentare cu aer:
Connect the tool to a clean, dry, regulated compressed air supply. Ensure the air pressure is within the recommended range (typically 90 PSI / 6.2 bar). Use an air hose with an adequate diameter to ensure proper airflow.
- Lubrifiere:
Before first use, and regularly thereafter, apply a few drops of pneumatic tool oil into the air inlet. This lubricates the internal components and extends tool life.
- Mandrel and Anvil Installation (if not pre-installed):
Ensure the correct size mandrel and anvil are securely installed for the 1/4-20 inserts. Refer to the tool's specific diagram for proper assembly. Tighten all components firmly.
- Ajustare adâncime:
Adjust the depth setting collar to achieve the desired flushness or protrusion of the installed insert. Test on a scrap piece of material before final application.
Instrucțiuni de operare
- Pregătiți piesa de lucru:
Drill a hole of the correct diameter for the 1/4-20 insert in the material. Ensure the hole is clean and free of debris.
- Load the Insert:
Thread the 1/4-20 insert onto the tool's mandrel until it is snug against the anvil.
- Poziționați instrumentul:
Place the insert into the prepared hole in the workpiece. Ensure the tool is held perpendicular to the surface.
- Instalați inserția:
Press the trigger to activate the tool. The mandrel will spin, pulling the insert into the material and deforming it to create a secure thread. Continue until the insert is fully seated and the tool stalls or reaches the set depth.
- Retract the Mandrel:
Release the trigger. Press the reverse button (if applicable) or allow the tool to automatically reverse, then carefully withdraw the tool from the newly installed insert.
- Inspectați instalarea:
Visually inspect the installed insert to ensure it is flush and securely fastened.
Întreţinere
- Lubrifiere zilnică: Add 5-10 drops of pneumatic tool oil into the air inlet before each use or at the start of each shift.
- Curăţenie: Keep the tool clean and free of dirt, dust, and debris. Wipe down the exterior with a clean cloth.
- Air Filter/Regulator: Regularly check and drain moisture from your air compressor's filter/regulator. Ensure the air supply is clean and dry.
- Mandrel/Anvil Inspection: Periodically inspect the mandrel and anvil for wear or damage. Replace worn components to ensure proper insert installation.
- Depozitare: Store the tool in a dry, clean environment when not in use.
Depanare
| Problemă | Cauza posibila | Soluţie |
|---|---|---|
| Unealta nu funcționează sau are putere redusă. | Low air pressure; insufficient air flow; lack of lubrication; clogged air inlet. | Check air pressure and hose size; add pneumatic tool oil; clean air inlet. |
| Insert not installing correctly (e.g., not fully collapsing). | Incorrect mandrel/anvil size; worn mandrel/anvil; incorrect depth setting; insufficient air pressure. | Verify mandrel/anvil size; replace worn parts; adjust depth setting; check air pressure. |
| Tool jams or struggles to retract. | Insert over-installed; damaged insert; mandrel stuck. | Adjust depth setting; ensure inserts are not damaged; inspect mandrel for wear. |
Specificații
| Caracteristică | Detaliu |
|---|---|
| Model | AE803-2520 |
| Tip de instrument | Pistol Spin/Spin Pneumatic Insert Tool |
| Thread Adapter Kit | 1/4-20 |
| RPM | 600 RPM |
| Greutatea articolului | 8.5 lire sterline |
| Producător | Atlas |
Garanție și suport
For warranty information, technical support, or to order replacement parts, please contact your authorized Atlas dealer or visit the official Atlas Tools webPăstrați bonul fiscal ca dovadă a achiziției.
For further assistance, please refer to the contact information provided with your purchase or on the manufacturer's official website-ul.
