SkyTech SKY-TS-R-2-A Fireplace Remote and Thermostat System User Manual

Introducere

The SkyTech TS/R-2-A remote control system is designed to provide safe and reliable operation for gas heating appliances. This system allows for both thermostatic and manual control from the transmitter. It operates using radio frequencies (RF) within a 20-foot range, utilizing non-directional signals and one of 1,048,576 security codes for secure communication. The remote receiver, powered by four AA batteries, processes commands from the transmitter to manage the appliance's operation.

This manual provides detailed instructions for the installation, operation, and maintenance of your SkyTech TS/R-2-A system.

Componentele sistemului

The SkyTech TS/R-2-A system includes the following components:

• Transmiţător: The handheld or wall-mounted unit with an LCD screen and control buttons.
• Receptor: The unit that connects to the gas appliance and receives signals from the transmitter.
• Wall Clip: For mounting the transmitter.
• Placă de perete: For mounting the receiver in a wall.
• Wires with Connectors: For connecting the receiver to the gas appliance.
• Baterii: Required for both transmitter and receiver.
• Manual de instructiuni: Acest document.

Imagine: Pesteview of the SkyTech TS/R-2-A system components, including the receiver, transmitter, and wall plate.

Configurare și instalare

1. Instalarea bateriei

Transmiţător: Insert the specified batteries into the transmitter. Ensure correct polarity. The LCD screen should activate. (Typically uses AAA or similar small batteries, not explicitly detailed in product data).

Receptor: Insert four AA batteries into the receiver. The receiver is designed for millivolt gas valves only and acts as a dry contact switch, meaning it will not output any voltage.

2. Plasarea receptorului

The receiver can be installed in several locations:

• Behind the included faceplate in a wall.
• On the hearth.
• Under the fireplace, behind the control access panel.

Ensure the receiver is placed within 20 feet of the intended transmitter location for optimal signal reception.

3. Cablarea receptorului

Connect the receiver to your gas heating appliance using the provided wires with connectors. Refer to your appliance's manual for specific wiring instructions for a remote control system. The receiver acts as a simple on/off switch for the millivolt gas valve.

4. Pairing (Learning Function)

To establish communication between the transmitter and receiver:

1. Locate the "LEARN" button on the receiver.
2. Press and hold the "LEARN" button on the receiver until you hear a beep or see an indicator light flash (refer to receiver specific indicators).
3. Within 10 seconds, press any button on the transmitter (e.g., "ON" or "SET").
4. The receiver should emit a confirmation sound or light, indicating successful pairing.

Note: If pairing fails, ensure both units have fresh batteries and are within range, then repeat the process.

Instrucțiuni de operare

Receiver Mode Selection

The receiver has a 3-position slide switch for selecting the mode of operation:

• PE: The gas appliance will remain continuously on, bypassing remote control.
• LA DISTANTA: The gas appliance will operate according to commands from the transmitter.
• OPRIT: The gas appliance will remain continuously off, bypassing remote control.

Set the receiver switch to TELECOMANDĂ for normal operation with the transmitter.

Funcțiile emițătorului

The transmitter features an LCD screen and three buttons: ON, SET, și OFF, along with up/down arrows.

• Display LCD: Shows the current room temperature and the set temperature (in Fahrenheit or Celsius).
• Buton ON: Manually turns the gas appliance on.
• Buton OFF: Manually turns the gas appliance off.
• Buton SET: Used to enter thermostatic mode and adjust the desired temperature.
• Săgeți sus/jos: Used to adjust the set temperature in thermostatic mode.

Operare manuală

To manually control the appliance:

• Apăsați tasta ON butonul pentru a porni aparatul.
• Apăsați tasta OFF pentru a opri aparatul.

Thermostatic Operation

To operate the appliance thermostatically:

1. Ensure the receiver switch is set to TELECOMANDĂ.
2. Apăsați tasta SET button on the transmitter. The set temperature will flash on the LCD.
3. Utilizați Up or Jos butoanele săgeată pentru a regla temperatura dorită.
4. Presa SET again or wait a few seconds for the setting to be saved.

The appliance will now cycle on and off to maintain the set temperature. Typically, the system activates when the room temperature drops a few degrees below the set temperature and turns off when it reaches a few degrees above the set temperature.

Modificarea unităților de temperatură (°F/°C)

The LCD screen displays temperature in Fahrenheit (°F) or Celsius (°C). Consult the transmitter's specific instructions (often a small switch or button combination) to toggle between these units if needed.

Întreţinere

Înlocuirea bateriei

Replace batteries in both the transmitter and receiver annually, or immediately if the display becomes dim, the range decreases, or the system becomes unresponsive. Low batteries can lead to communication issues and unexpected system behavior.

• Transmiţător: Typically uses AAA or similar small batteries. Refer to the battery compartment for exact type.
• Receptor: Uses 4 AA batteries.

Always use fresh, high-quality alkaline batteries. Dispose of old batteries responsibly.

Curatenie

Wipe the transmitter and receiver with a soft, dry cloth. Do not use abrasive cleaners or immerse the units in water.

Depanare

• Sistemul nu răspunde:
  • Check batteries in both transmitter and receiver. Replace if low.
  • Ensure the receiver's slide switch is set to TELECOMANDĂ.
  • Verify the transmitter and receiver are within the 20-foot operating range.
  • Re-attempt the pairing (learning) process.
• Appliance Does Not Turn On/Off in Thermostatic Mode:
  • Confirm the set temperature is appropriate for the desired operation (e.g., set higher than room temp to turn on).
  • Check for significant temperature fluctuations or drafts near the transmitter that might affect readings.
  • Ensure the receiver is properly wired to the gas appliance.
• Citire inexactă a temperaturii:
  • Ensure the transmitter is not placed near heat sources, direct sunlight, or drafts that could skew readings.
  • Compare the transmitter's reading with another reliable thermometer in the same location. Small discrepancies (1-3 degrees) can occur due to placement or sensor variations.
• Funcționare intermitentă:
  • This can often be caused by low batteries. Replace them.
  • Check for sources of radio frequency interference (e.g., other wireless devices, large metal objects) between the transmitter and receiver.

Specificații

Garanție și suport

Specific warranty information for the SkyTech TS/R-2-A system is not provided in this manual. For details regarding warranty coverage, please refer to the documentation included with your purchase or contact SkyTech customer support directly.

For technical assistance or further inquiries, please visit the official SkyTech website-ul web sau contactați departamentul de asistență pentru clienți. Informațiile de contact se găsesc de obicei pe ambalajul produsului sau pe fișa producătorului. website-ul.