1. Introducere
This manual provides detailed instructions for the installation and basic maintenance of the Generic replacement water pump, model Fricpart-100476, designed for compatibility with Kenmore Dishwasher Model 665.13463K900. Please read this manual thoroughly before beginning any installation or maintenance procedures to ensure safe and correct operation.
2. Informații de siguranță
- Always disconnect power to the dishwasher before attempting any repairs or installations.
- Opriți alimentarea cu apă a mașinii de spălat vase înainte de a începe lucrul.
- Purtați echipament individual de protecție adecvat, cum ar fi mănuși și ochelari de protecție.
- Dacă nu sunteți sigur de vreun pas, consultați un tehnician calificat în domeniul electrocasnicelor.
- Păstrați piesele mici departe de copii.
3. Instrucțiuni de instalare
This section outlines the general steps for replacing the dishwasher water pump. Specific disassembly and reassembly steps for your Kenmore 665.13463K900 model may vary slightly. Refer to your dishwasher's original service manual for detailed model-specific instructions.
3.1 Instrumente necesare
- Șurubelnițe (Phillips și Flathead)
- Cleşte
- Cheie reglabila
- Towels or rags for water spills
- Bucket or shallow pan
3.2 Pregătire
- Deconectați alimentarea: Locate the circuit breaker for your dishwasher and turn off the power. Verify power is off by attempting to start the dishwasher.
- Opriți alimentarea cu apă: Locate the water shut-off valve for the dishwasher, usually under the sink, and turn it off.
- Scurgerea apei: If there is standing water in the dishwasher tub, manually drain it using a cup or sponge.
- Access Dishwasher: Carefully pull the dishwasher out from its cabinet enclosure to access the underside. You may need to disconnect the drain hose and water supply line if they are too short.
3.3 Removing the Old Water Pump
- Locate Pump: Identify the water pump assembly, typically located at the bottom of the dishwasher tub.
- Deconectați cablarea: Carefully disconnect any electrical wiring harnesses connected to the pump motor. Note their positions for reassembly.
- Deconectați furtunurile: Slăbiți și îndepărtați clamps securing the water hoses to the pump. Be prepared for residual water to spill; have towels and a bucket ready.
- Remove Mounting: Unfasten any screws, clips, or brackets holding the pump assembly in place.
- Extract Pump: Carefully remove the old water pump assembly from the dishwasher.
Figura 1: Generic Replacement Dishwasher Water Pump (Fricpart-100476). This image shows the complete water pump assembly, featuring a grey housing, a white central body, and a yellow impeller with multiple blades. This is the component you will be installing.
3.4 Installing the New Water Pump
- Poziția noii pompe: Carefully place the new Fricpart-100476 water pump into the dishwasher, ensuring it aligns correctly with the mounting points.
- Montare sigură: Fasten the pump with the screws, clips, or brackets removed earlier. Ensure it is securely in place.
- Reconectați furtunurile: Attach the water hoses to the new pump and secure them with their clamps. Asigurați o etanșare etanșă pentru a preveni scurgerile.
- Reconectați cablajul: Reconnect all electrical wiring harnesses to the pump motor. Double-check that all connections are firm and correct.
3.5 Pași finali
- Reposition Dishwasher: Carefully slide the dishwasher back into its cabinet enclosure. Reconnect the drain hose and water supply line if they were disconnected.
- Restabilirea alimentării cu apă: Turn on the water shut-off valve. Check for any immediate leaks around the pump and hose connections.
- Restabiliți puterea: Turn on the circuit breaker for the dishwasher.
- Funcționare de testare: Run a short wash cycle and carefully observe the dishwasher for proper operation and any leaks.
4. Întreținere
The water pump is a sealed unit and generally requires no routine maintenance. However, to ensure its longevity and the overall performance of your dishwasher:
- Regularly clean the dishwasher filter to prevent debris from reaching the pump.
- Avoid overloading the dishwasher, which can strain the pump.
- Folosiți detergenți și agenți de clătire adecvați pentru mașina de spălat vase.
- Inspect hoses and connections periodically for signs of wear or leaks.
5. Depanare
If you encounter issues after installing the new water pump, consider the following common problems and solutions:
| Problemă | Cauza posibila | Soluţie |
|---|---|---|
| Mașina de spălat vase nu scurge | Clogged drain hose, faulty drain pump (if separate), or electrical connection issue. | Check drain hose for kinks or blockages. Verify electrical connections to the pump. If the issue persists, the drain pump (if separate from the wash pump) may need inspection. |
| Mașina de spălat vase nu se umple cu apă | Water supply valve off, clogged inlet screen, or faulty water inlet valve. | Ensure water supply is on. Check the inlet screen for debris. This issue is typically not related to the water pump itself. |
| Loud noise during wash cycle | Debris in pump impeller, incorrect installation, or a defective pump. | Disconnect power and water, then inspect the pump impeller for foreign objects. Recheck mounting for secure installation. If noise persists, the pump may be faulty. |
| Water leaks from pump area | Închidere furtun slăbităamps, damaged gasket/seal, or cracked pump housing. | Strângeți furtunul clamps. Inspect gaskets and seals for proper seating and damage. Ensure the pump housing is intact. |
Dacă pașii de depanare nu rezolvă problema, se recomandă contactarea unui tehnician calificat în repararea electrocasnicelor.
6. Specificații
- Tip piesa: Replacement Dishwasher Water Pump
- Compatible Dishwasher Model: Kenmore 665.13463K900
- Replacement Part Model: Fricpart-100476
- Producător: Fricparts
- Culoare: Black/White (housing), Yellow (impeller)
- ASIN: B0FDH7FWCL
