Tridonic Linear Excite USB Series LED Driver Instruction Manual

1. Introducere

This manual provides essential information for the safe and efficient installation, operation, and maintenance of the Tridonic Linear Excite USB Series 35 Watts Constant Current LED Driver. This device is designed for professional lighting applications, offering adjustable output current and 0-10V dimming capabilities.

Vă rugăm să citiți cu atenție acest manual înainte de instalare și să îl păstrați pentru referințe ulterioare.

2. Informații de siguranță

AVERTIZARE: Risk of electric shock. Installation and servicing should only be performed by qualified personnel. Disconnect power before installation or servicing.

• This device is UL Listed (E345983), Class P, and Class 2 compliant, meeting UL8750 and UL1310 standards.
• Meets FCC Part 15 Class A for electromagnetic compatibility.
• Meets UL 8750 SF3.1 Isolation and strictest flicker-free performance standards.
• Potrivit pentru uscat și damp locations (IP20 rated).
• For connection, use wire rated for at least 90°C (194°F).
• ATENŢIE: Ensure only one power supply is present for the connected load to avoid damage or hazard.

3. Produs terminatview și Caracteristici

The Tridonic Linear Excite USB Series LED Driver is a high-performance constant current power supply for LED modules. Key features include:

• Ieșire curent constant: Adjustable between 150mA and 1,050mA in 1mA increments via USB programming.
• Eficiență ridicată: Up to 90% efficiency, minimizing energy waste.
• Reglare 0-10V: Smooth, flicker-free dimming from 0% to 100% via a 0-10V interface.
• 12V AUX Output: Provides a 12V auxiliary output to power sensors or additional control devices.
• Protecție robustă: Integrated safeguards against over-temperature, short-circuit, overload, no-load conditions, and improper input voltage.
• Design durabil: Housed in a white metal casing with IP20 protection, suitable for dry and damp medii.
• Durata de viata lunga: Nominal lifetime of up to 50,000 hours.

4. Configurare și instalare

Before beginning installation, ensure the main power supply is disconnected.

4.1 Montare

Mount the LED driver in a location that allows for adequate ventilation and is within its specified operating temperature range (tc = +75 °C max). The IP20 rating indicates suitability for dry and damp indoor locations. Secure the driver using appropriate fasteners through the designated mounting points on the metal casing.

4.2 Conexiuni de cablare

Refer to the product label and the diagram below for correct wiring. All connections must be secure and comply with local electrical codes.

Un deasupra capului view of the Tridonic Linear Excite USB Series LED Driver. The image shows the input terminals (L BLK, N WHI, G GRN) on the left, the product model number (LC 35/150-1050/54 0-10V AUX lp EXC UNV), and the output terminals (LED+ RED, LED- BLU, 700mA SET ORG, +12V YLW, DIM+ PUR, DIM- PINK) on the right. Various specifications and certifications like UL and CE are printed on the device casing.

• Input (AC Mains):
  • L (BLK): Connect to Live/Phase (Black wire).
  • N (WHI): Connect to Neutral (White wire).
  • G (GRN): Connect to Ground (Green wire).
• Output (DC to LED Module):
  • LED+ (RED): Connect to the positive terminal of the LED module.
  • LED- (BLU): Connect to the negative terminal of the LED module.
• Dimming Control (0-10V):
  • DIM+ (PUR): Connect to the positive terminal of the 0-10V dimmer.
  • DIM- (PINK): Connect to the negative terminal of the 0-10V dimmer.
• Ieșire auxiliară:
  • +12V (YLW): Provides 12V DC output for external devices.
• Setare curentă:
  • 700mA SET (ORG): This terminal is for specific current setting configurations, typically used for factory default or specific programming. Refer to advanced programming instructions if needed.

5. Instrucțiuni de utilizare

5.1 Pornire

Once all connections are securely made and verified, restore power to the LED driver. The connected LED module should illuminate.

5.2 Reglare luminoasă 0-10V

The driver supports 0-10V dimming. Connect a compatible 0-10V dimmer to the DIM+ and DIM- terminals. Adjusting the voltage from 0V to 10V will linearly control the LED output from 0% to 100% brightness. A 0V input will dim the LEDs to off.

5.3 Output Current Adjustment (USB Programming)

The output current of the LED driver can be precisely adjusted from 150mA to 1,050mA in 1mA steps using Tridonic's USB programming interface and software (sold separately). This allows for customization to match specific LED module requirements. Refer to the Tridonic programming guide for detailed instructions on using the USB interface.

5.4 12V AUX Output

The 12V AUX output (YLW wire) can be used to power low-voltage auxiliary devices such as sensors or control modules, provided their current draw does not exceed the driver's auxiliary output capacity.

6. Întreținere

The Tridonic LED driver is designed for long-term, maintenance-free operation. However, periodic inspection is recommended:

• Ensure the driver's casing is free from dust and debris to maintain proper heat dissipation.
• Verificați etanșeitatea și integritatea tuturor conexiunilor cablajului.
• Verify that the ambient temperature around the driver does not exceed its specified operating limits.
• Do not attempt to open or repair the driver. Refer servicing to qualified personnel.

7. Depanare

If the LED driver or connected lighting system is not functioning as expected, consider the following:

• Fara iesire de lumina:
  • Check if the main power supply is connected and active.
  • Verify all input and output wiring connections are correct and secure.
  • Ensure the LED module is correctly connected and not faulty.
  • Check the 0-10V dimmer setting; it might be set to 0V (off).
• Lumină pâlpâitoare sau instabilă:
  • Inspect wiring for loose connections or damage.
  • Ensure the 0-10V dimmer is compatible and functioning correctly.
  • Verificați volumul de intraretage se încadrează în intervalul specificat (120-277 V CA).
• Incorrect Brightness or Dimming Issues:
  • Confirm the 0-10V dimmer is properly connected and calibrated.
  • If output current was programmed via USB, ensure the correct current setting was applied.
• Supraîncălzirea șoferului:
  • Asigurați o ventilație adecvată în jurul șoferului.
  • Verify the ambient temperature is within operating limits.
  • Check if the load connected to the driver exceeds its maximum output power (35W).

If issues persist after troubleshooting, contact Tridonic technical support or an authorized service provider.

8. Specificații

9. Garantie

This Tridonic LED driver comes with a 5-year warranty, valid for operating conditions where the maximum case temperature (tc) does not exceed 75 °C. Please retain your proof of purchase for warranty claims. For full warranty terms and conditions, refer to the official Tridonic website-ul sau contactați asistența pentru clienți.

10. Suport

For technical assistance, product inquiries, or service requests, please contact Tridonic customer support or your authorized Tridonic distributor. Visit the official Tridonic website for the latest product information, software updates, and contact details.