Xigmatek Endorphin WD Mid-Tower PC Case User Manual

1. Introducere

Thank you for choosing the Xigmatek Endorphin WD Mid-Tower PC Case. This case is designed to provide an optimal balance of aesthetics and functionality, featuring a tempered glass side panel and a distinctive wooden facade. It supports Micro ATX and ATX motherboards and comes equipped with four 120mm ARGB fans for efficient cooling and vibrant lighting. This manual provides detailed instructions for assembly, operation, and maintenance to ensure a smooth and enjoyable experience with your new PC case.

Figura 1.1: Față view of the Xigmatek Endorphin WD PC case, showcasing its unique wooden facade and the vibrant ARGB fans visible through the front panel.

2. Informații de siguranță

Please read these safety instructions carefully before installing or using the PC case. Failure to follow these guidelines may result in injury or damage to your components.

• Always disconnect the power supply from the wall outlet before performing any installation or maintenance inside the case.
• Handle tempered glass panels with care. They are fragile and can shatter if dropped or struck forcefully.
• Avoid touching electronic components directly to prevent electrostatic discharge (ESD). Use an anti-static wrist strap if available.
• A nu se lăsa la îndemâna copiilor piesele mici și șuruburile.
• Asigurați o ventilație adecvată în jurul carcasei PC-ului pentru a preveni supraîncălzirea.

3. Conținutul pachetului

Verificați dacă toate articolele sunt prezente în colet:

• Xigmatek Endorphin WD Mid-Tower PC Case
• Accessory box (containing screws, cable ties, and other small parts)
• Manual de utilizare (acest document)

4. Configurare și instalare

Follow these steps to install your PC components into the Xigmatek Endorphin WD case.

4.1. Deschiderea carcasei

1. Așezați carcasa pe o suprafață plană și stabilă.
2. Carefully remove the tempered glass side panel by unscrewing the thumbscrews located at the rear of the case. Gently pull the panel away and set it aside on a soft, non-abrasive surface.
3. Remove the opposite metal side panel by unscrewing its thumbscrews and sliding it backward, then lifting it off.

Figura 4.1: lateral view of the Xigmatek Endorphin WD PC case, illustrating the tempered glass side panel that can be removed for component installation.

4.2. Instalarea plăcii de bază

1. Install the I/O shield that came with your motherboard into the designated opening at the rear of the case.
2. Ensure that the standoffs for your motherboard form factor (Micro ATX or ATX) are correctly installed on the motherboard tray. Adjust or add standoffs as necessary using the provided tools.
3. Carefully align your motherboard with the standoffs and the I/O shield, then gently lower it into place.
4. Fixați placa de bază cu șuruburile corespunzătoare din cutia de accesorii. Nu strângeți prea tare.

Figura 4.2: Interior view of the Xigmatek Endorphin WD PC case, highlighting the spacious motherboard tray and various mounting points for components.

4.3. Instalarea unității de stocare

The case supports 3.5-inch and 2.5-inch drives.

• HDD-uri de 3.5 inci: Locate the drive cages, typically near the bottom rear of the case. Slide the HDD into a drive bay and secure it with screws.
• 2.5-inch SSDs/HDDs: Mount these drives to the designated brackets on the back of the motherboard tray or within the drive cages, securing them with screws.

4.4. Instalarea sursei de alimentare

The power supply unit (PSU) mounts at the rear of the case.

1. Slide your ATX power supply into the dedicated compartment at the bottom rear of the case.
2. Align the PSU with the screw holes at the rear of the case.
3. Secure the PSU with the four screws provided in your PSU's accessory kit or the case's accessory box.

Figura 4.3: Spate view of the Xigmatek Endorphin WD PC case, detailing the power supply mounting area and the arrangement of expansion slots.

4.5. Instalarea plăcii de expansiune (de exemplu, placa grafică)

1. Scoateți capacele sloturilor de expansiune necesare din spatele carcasei.
2. Align your expansion card with the PCIe slot on your motherboard and gently press it down until it clicks into place.
3. Secure the card to the case with the provided screws.

4.6. Conectarea intrărilor/ieșirilor de pe panoul frontal

Connect the front panel cables to the corresponding headers on your motherboard. Refer to your motherboard manual for exact pin layouts.

• USB 2.0: Connect the USB 2.0 cable to a 9-pin USB 2.0 header.
• USB 3.0: Connect the USB 3.0 cable to a 19-pin USB 3.0 header.
• Audio: Connect the HD Audio cable to the F_AUDIO header.
• Power/Reset/LEDs: Connect the individual Power SW, Reset SW, HDD LED, and Power LED cables to the front panel header.

4.7. Gestionarea cablurilor

Folosește decupajele pentru rutarea cablurilor și punctele de fixare din spatele tăvii plăcii de bază pentru a gestiona cablurile cu grijă. Acest lucru îmbunătățește fluxul de aer și aspectul estetic.

5. Instrucțiuni de utilizare

5.1. Powering On Your PC

Once all components are installed and cables are connected, replace the side panels. Connect your monitor, keyboard, mouse, and power cable to the PC. Flip the switch on your power supply to the 'ON' position, then press the power button on the front of the case.

5.2. Controlul iluminării ARGB

The Xigmatek Endorphin WD comes with four pre-installed 120mm ARGB fans. These fans can be controlled via your motherboard's ARGB software (if your motherboard supports 5V 3-pin ARGB headers) or through a dedicated ARGB controller if one is included or purchased separately. Refer to your motherboard or controller manual for specific instructions on changing lighting effects.

6. Întreținere

Întreținerea regulată ajută la asigurarea performanței optime și a longevității componentelor PC-ului.

• Filtre de praf: The case is equipped with dust filters to prevent dust buildup. Periodically remove and clean these filters with compressed air or by washing them with water (ensure they are completely dry before reinstallation).
• Curatenie interioara: Every few months, open the case and use compressed air to remove dust from fans, heatsinks, and other components.
• Curatenie exterioara: Ștergeți suprafețele exterioare cu un material moale, damp cloth. Avoid harsh chemicals that may damage the finish or the wooden facade.

7. Depanare

Dacă întâmpinați probleme, luați în considerare următorii pași comuni de depanare:

• PC-ul nu pornește: Ensure the power cable is securely connected to both the PSU and the wall outlet. Check that the PSU switch is in the 'ON' position. Verify that the front panel power switch cable is correctly connected to the motherboard.
• Fans Not Spinning/ARGB Not Working: Check all fan and ARGB connections to the motherboard or controller. Ensure power cables are connected to the fans/controller. Verify that ARGB software is correctly configured.
• Fără ieșire de afișare: Ensure your monitor is connected to the graphics card (not the motherboard's integrated graphics ports, unless you are using integrated graphics). Reseat your graphics card and RAM modules.
• Supraîncălzire: Ensure all case fans are spinning correctly and are oriented to provide adequate airflow (intake and exhaust). Clean dust filters and internal components.

8. Specificații

9. Informații despre garanție

The Xigmatek Endorphin WD PC Case comes with a 2 an garanție from the date of purchase. This warranty covers manufacturing defects and faulty materials under normal use. It does not cover damage caused by misuse, accident, modification, or unauthorized repair. Please retain your proof of purchase for warranty claims.

10. Suport

For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact Xigmatek customer support through their official website or your local retailer. Have your product model and proof of purchase ready when contacting support.

Official Xigmatek Website: www.xigmatek.com