Amewi Hyper GO Truggy 1:14 Brushless 4WD RC Vehicle Instruction Manual

1. Informații importante privind siguranța

Please read this manual carefully before operating the Amewi Hyper GO Truggy. Failure to follow these instructions may result in injury or damage to the product.

• Avertizare! Not suitable for children under three years of age. Choking hazard due to small parts.
• Recommended age for operation: Adolescents and Adults (14+ years).
• Always operate the vehicle in a safe, open area, away from people, pets, and obstacles.
• Do not operate near public roads, water, or high-voltagliniile electrice.
• Țineți mâinile, părul și hainele largi departe de părțile mobile.
• Ensure all electronics are protected from water splashes during outdoor use.
• Nu lăsați niciodată bateria încărcată nesupravegheată.
• Folosiți doar cablul de încărcare furnizat și surse de alimentare compatibile.

2. Conținutul pachetului

The Amewi Hyper GO Truggy RTR (Ready-To-Run) package includes the following components:

• Amewi Hyper GO Truggy (Model 22659)
• 3-Channel 2.4 GHz Remote Control
• 2S LiPo Battery (7.4V, 3000mAh, 25C)
• USB Balance Charging Cable (7.4V, 1.5A output)
• Additional Gold-colored Body Shell
• Set of Sand Tires
• Spare Parts (e.g., front wishbones, body mounts, spare rear wing)
• Tool Kit (e.g., screw set)
• Body Clips with Rubber Tabs
• Manual de instrucțiuni (acest document)

Nota: Two AA 1.5V batteries for the remote control are required and not included in the package.

3. Configurare

3.1. Încărcarea bateriei LiPo

The included LiPo battery must be fully charged before first use. Always follow LiPo battery safety guidelines.

1. Connect the USB balance charging cable to a compatible USB power adapter (not included).
2. Connect the LiPo battery to the charging cable. Ensure the connectors are correctly aligned.
3. The charging indicator on the cable will show the charging status (e.g., red for charging, green for fully charged).
4. Timpul de încărcare este de aproximativ 150-180 de minute. Nu supraîncărcați.
5. Once charged, disconnect the battery from the charger and store it safely.

Image: The included 2S 7.4V 3000mAh LiPo battery for the Amewi Hyper GO Truggy.

3.2. Instalarea bateriilor telecomenzii

Insert two AA 1.5V batteries (not included) into the remote control's battery compartment. Ensure correct polarity.

3.3. Installing the Vehicle Battery

1. Remove the body clips and carefully lift the vehicle's body shell.
2. Place the charged LiPo battery into the battery compartment.
3. Connect the battery to the vehicle's ESC (Electronic Speed Controller) connector.
4. Secure the battery if necessary and reattach the body shell with the clips.

4. Instrucțiuni de utilizare

4.1. Pornire și împerechere

1. Porniți mai întâi telecomanda.
2. Turn on the vehicle's power switch.
3. The remote control and vehicle should automatically pair. If not, refer to the troubleshooting section.

4.2. Controale de bază

• Volan: Virați la stânga sau la dreapta pentru a controla direcția vehiculului.
• Declanșator de accelerație: Trageți pentru a accelera înainte, împingeți pentru a frâna sau a da înapoi.
• Ajustări de trim: Use the steering trim and throttle trim dials on the remote control to fine-tune straight-line tracking and neutral throttle position.
• Faruri: The 3-channel remote control features an additional button to turn the front LED headlights on or off.

4.3. Speed Limiter

The remote control includes a switch to limit the maximum speed to 70%. This is useful for beginners or when operating in smaller spaces.

4.4. Sfaturi de conducere

• Începeți cu viteze mici pentru a vă obișnui cu comenzile.
• The vehicle is equipped with large, high-grip soft rubber tires for excellent traction on various surfaces.
• For sand driving, utilize the included sand tires for optimal performance.
• The Wheelie Bar provides increased driving stability, especially during rapid acceleration.
• The 2.4 GHz system allows multiple models to operate simultaneously without interference.

Image: The Amewi Hyper GO Truggy in its standard black body, ready for operation.

5. Întreținere

Regular maintenance ensures the longevity and performance of your Amewi Hyper GO Truggy.

• curatenie: After each use, especially in dusty or dirty conditions, clean the vehicle with a soft brush or compressed air. Avoid using water directly on electronics.
• Inspecţie: Regularly check for loose screws, damaged parts, or worn tires. Tighten screws as needed.
• Componentele unității: The drive components (gears and differentials) are made of metal for high durability. Inspect them periodically for wear and lubricate if necessary.
• Amortizoare: The aluminum oil-pressure shock absorbers should be checked for leaks or damage.
• Motor Fan: The active fan on the motor ensures optimal cooling. Keep it free from debris.
• Stocare baterie: Store LiPo batteries in a cool, dry place at a storage voltage (aproximativ 3.8 V per celulă) dacă nu este utilizată pentru perioade lungi de timp.

6. Depanare

If you encounter issues with your Amewi Hyper GO Truggy, refer to the following common problems and solutions:

7. Specificații

8. Garanție și asistență

8.1. Garanția producătorului

Manufacturer's warranty information is not explicitly specified in the product details. Please retain your proof of purchase for any warranty claims. For specific warranty terms, contact Amewi directly.

8.2. Asistență pentru clienți

For technical assistance, spare parts, or further inquiries, please contact Amewi customer support. Refer to the official Amewi website-ul sau ambalajul produsului pentru cele mai recente informații de contact.

Amewi GmbH
Address: [Refer to official Amewi website for current address]
Website: www.amewi.com