Produs terminatview
The DAYBETTER 44-Key Remote Control is designed to manage 12-24V DC 4-pin LED strip lights, offering a wide range of color and mode options. It features a dual-port connector, allowing control of one or two LED strips simultaneously.
DAYBETTER 44-Key Remote Control and Controller Box with LED Strip Lights
Conținutul pachetului
- 1 x Telecomandă IR cu 44 de taste
- 1 x LED Controller Box (with two 4-pin output ports)
- 1 x adaptor de alimentare
Instrucțiuni de configurare
Follow these steps to properly set up your DAYBETTER LED strip light system.
- Step 1: Prepare the Remote Control. Before first use, locate the plastic insulation tab in the battery compartment of the 44-key remote control. Pull this tab out to activate the battery.
- Step 2: Connect LED Strips to the Controller. Ensure the power adapter is disconnected. Connect your 4-pin LED strip lights to the output ports on the LED controller box. Align the arrow on the LED strip connector with the arrow on the controller's output port. The controller box has two 4-pin ports, allowing connection of one or two LED strips.
- Step 3: Connect Power Adapter. Connect the power adapter to the DC input port on the LED controller box.
- Step 4: Connect to Power Source. Plug the power adapter into a suitable 12-24V DC power outlet.
Removing the plastic insulation tab from the remote control battery compartment.
Proper alignment of 4-pin LED strip connector with the controller port, ensuring arrow-to-arrow connection.
A închide view of the LED controller box, showing the DC power input port and IR sensor.
Diagram illustrating the complete connection process: Power Adapter to IR Receiver, IR Receiver to LED Controller, and LED Controller to LED Strip Lights, highlighting correct 4-pin connector orientation.
Operating Your LED Controller
The 44-key remote control allows for comprehensive control over your LED strip lights. Ensure the remote is pointed directly at the IR sensor on the controller box within approximately 30 feet for optimal functionality.
Diagram of the 44-key remote control, detailing the function of each button for color selection, brightness adjustment, and mode changes.
- Pornire/Oprire: Apăsați tasta ON/OFF buton pentru a aprinde sau stinge luminile.
- Reglarea luminozității: Utilizați Luminozitate crescută (săgeată în sus) și Scăderea luminozității (down arrow) buttons to adjust the light intensity (7 levels).
- Culori statice: Select from 20 static colors by pressing the corresponding color buttons.
- RGB Adjustment: Utilizați R, G, B buttons to fine-tune red, green, and blue color levels.
- Quick/Slow: Adjust the speed of dynamic modes (Jump3, Jump7, Fade3, Fade7, Flash) using the RAPID şi LENT butoane.
- Mod auto: Presa AUTO for automatic color cycling through various modes.
- Modul bliț: Activates a rapid flashing effect.
- Fade Modes:
- FADE7: Gradually fades through 7 colors.
- FADE3: Gradually fades through 3 colors.
- Moduri de salt:
- JUMP7: Jumps between 7 colors.
- JUMP3: Jumps between 3 colors.
- DIY Buttons (DIY1-DIY6): These buttons allow you to save custom color settings. To set a custom color:
- Apăsați a DIY buton.
- Utilizați R, G, B adjustment arrows to create your desired color.
- Apăsați la fel DIY button again to save the color.
Întreţinere
- curatenie: Use a dry, soft cloth to clean the controller and remote. Do not use liquid cleaners or abrasive materials.
- Înlocuire baterie: If the remote control's range or responsiveness decreases, replace the battery (CR2025 coin cell, not included). Ensure correct polarity.
- Depozitare: Depozitați dispozitivul într-un loc răcoros și uscat, ferit de lumina directă a soarelui și de temperaturi extreme, atunci când nu îl utilizați pentru perioade lungi de timp.
Depanare
| Problemă | Soluţie |
|---|---|
| Luminile nu se aprind. | Check power connections. Ensure the power adapter is plugged in and the LED strips are correctly connected (arrow to arrow). Verify the remote control battery is active and correctly inserted. |
| Telecomanda nu răspunde. | Ensure the plastic insulation tab has been removed from the remote. Point the remote directly at the IR sensor on the controller box. Replace the remote control battery if necessary. The effective range is approximately 30 feet. |
| Luminile sunt slabe sau pâlpâie. | Check the power adapter for sufficient voltage (12-24V DC). Ensure all connections are secure. Reduce the length of the LED strip if it exceeds the controller's maximum current capacity (6A). |
| Incorrect colors displayed. | Ensure the 4-pin connectors are aligned correctly (arrow to arrow). Disconnect and reconnect the LED strips. |
| Only one LED strip works. | Verify both 4-pin connectors are properly inserted into the controller's dual ports. Check the connections of the non-working strip. |
Specificațiile produsului
- Model: DRF-0362-W
- Marca: ZI MAI BINE
- Tipul controlerului: 44-Key IR Remote Control
- Vol. De intraretage: 12-24V DC
- Porturi de ieșire: 2 x 4 pini
- Curent maxim: 6A
- Metoda de control: Infrared (IR) Remote
- Distanță: Approximately 30 feet (line of sight required)
- Material: Plastic
- Utilizare în interior/exterior: De interior
- Caracteristici speciale: Dimmable, 20 Static Colors, Dynamic Modes (Flash, Fade, Jump), DIY Color Saving
- Compatible LED Strips: 5050, 3528, 2835 (4-pin RGB)
Informații despre garanție
For warranty details, please refer to the product packaging or contact DAYBETTER customer service. Keep your purchase receipt as proof of purchase for any warranty claims.
Asistență pentru clienți
If you encounter any issues or have questions regarding your DAYBETTER 44-Key Remote Control, please contact DAYBETTER customer support through the retailer's platform or visit the official DAYBETTER website pentru asistență.