ErGear Dual Monitor Stand EGCM3-E Instruction Manual

Introducere

This manual provides detailed instructions for the assembly, operation, and maintenance of your ErGear Dual Monitor Stand, model EGCM3-E. Please read this manual thoroughly before installation and retain it for future reference. This monitor stand is designed to support two monitors ranging from 13 to 32 inches, with a maximum weight capacity of 8 kg (17.6 lbs) per arm.

Informații de siguranță

• Asigurați-vă că toate componentele sunt prezente și nedeteriorate înainte de asamblare. Nu utilizați produsul dacă lipsesc sau sunt defecte piesele.
• Do not exceed the maximum weight capacity of 8 kg (17.6 lbs) per arm. Overloading may result in instability and potential injury.
• This stand is compatible with VESA mounting patterns of 75x75mm and 100x100mm. Verify your monitor's VESA pattern before installation.
• Always use two people for lifting and mounting monitors to prevent injury.
• Asigurați-vă că suportul este așezat pe o suprafață stabilă și plană.
• Țineți copiii și animalele de companie departe în timpul asamblarii.

Conținutul pachetului

Vă rugăm să verificați dacă toate piesele sunt incluse în pachet:

• Placă de bază
• Pol de sprijin
• Brațe pentru monitor (2)
• Plăci VESA (2)
• Cleme de gestionare a cablurilor
• Set de accesorii (șuruburi, șaibe, chei Allen)

Instrucțiuni de configurare

Step 1: Assemble the Base and Pole

Attach the support pole to the base plate using the provided screws. Ensure the connection is secure and stable.

The sturdy base plate provides stability for the dual monitor setup. Dimensions are approximately 41cm by 26cm.

Step 2: Attach Monitor Arms to the Pole

Slide the monitor arms onto the support pole. Adjust them to your desired height and tighten the securing mechanism. Note that both arms adjust vertically together.

Pasul 3: Atașați plăcile VESA la monitoare

Secure the VESA plates to the back of your monitors using the appropriate screws from the hardware kit. Ensure the VESA pattern (75x75mm or 100x100mm) matches.

Each arm is designed to hold monitors up to 8 kg (17.6 lbs) and supports VESA 75x75mm or 100x100mm mounting patterns for 13-32 inch screens.

Pasul 4: Montați monitoarele pe brațe

Carefully slide the monitors (with VESA plates attached) onto the monitor arms. Secure them in place with the locking screws or clips provided.

Operare și reglaje

The ErGear Dual Monitor Stand offers a range of adjustments for optimal viewing comfort and ergonomic positioning.

Reglarea înălțimii

To adjust the height of both monitors, loosen the collar on the support pole, slide the arms to the desired height, and then re-tighten the collar. The maximum height extension is approximately 42cm.

Monitors can be raised up to 42cm from the desk surface to achieve an ergonomic viewînălțimea ing.

Înclinare, pivotare și rotație

Each monitor arm allows for flexible positioning:

• Înclinare: Adjust the monitor screen ±45° (up or down) to reduce glare and optimize viewunghiuri de ing.
• pivotare: Pivot the monitor 180° (left or right) to share your screen or change viewdirecție.
• Rotaţie: Rotiți monitorul la 360° pentru a comuta între orientarea peisaj și portret.

The stand allows for versatile adjustments including tilt, swivel, and full 360-degree rotation for each monitor.

Easily switch monitors between landscape and portrait modes for different tasks.

Managementul cablurilor

The stand features integrated cable management clips to keep your workspace tidy and organized. Route your monitor and power cables along the arms and down the support pole using the provided clips.

Utilize the integrated cable management system to maintain a clean and organized desk environment.

Întreţinere

• Verificați periodic toate șuruburile și conexiunile pentru a vă asigura că rămân strânse și fixate.
• Curățați suportul cu un material moale, damp Evitați utilizarea de produse de curățare abrazive sau solvenți.
• Do not lubricate any moving parts unless specifically instructed by the manufacturer.

Depanare

Monitoarele nu sunt la nivel:

Check if the VESA plates are securely attached to both monitors and the arms. Ensure the arms are at the same height on the pole. Minor adjustments can often be made by slightly loosening and re-tightening the VESA plate screws.

Standul pare instabil:

Verify that the base is on a flat, stable surface. Ensure all screws, especially those connecting the pole to the base, are fully tightened. Confirm that the combined weight of your monitors does not exceed the stand's capacity.

Dificultate la reglarea înclinării/rotației:

Some joints may have tension adjustment screws. Refer to the assembly diagrams for specific locations and use the provided Allen key to loosen or tighten as needed.

Specificații

Garanție și suport

For warranty information or technical support, please refer to the documentation included with your purchase or contact ErGear customer service directly. Contact details can typically be found on the manufacturer's official website-ul sau pe ambalajul produsului.