Introducere
The Autotek MM2020.1D The Mean Machine Monoblock Class D Amplifier is designed to deliver high power output with minimal distortion for a mono subwoofer system. Featuring Pro-Fi high-speed MOSFETs and Class D technology, this amplifier provides efficient power in a compact design. It offers flexible connectivity options, including RCA outputs for daisy-chaining multiple ampliificatori.
Informații de siguranță
AVERTISMENT: Acest produs conține substanțe chimice cunoscute de statul California pentru a provoca cancer și defecte congenitale sau alte vătămări reproductive.
Produs terminatview
Caracteristici cheie
- 2,000 watts mono bridged x 1 @ 4 ohms
- 500 watts x 1 @ 4 ohms
- 1,000 watts x 1 @ 2 ohms
- 0 to 12 dB bass boost
- Road Worthy TCID (Twin Coil Isolation Design) and Pro-Fi High Speed MOSFETS for extreme power with high sound quality and minimum distortion levels.
AmpLiifier Layout
Panoul din spate view of the Autotek MM2020.1D amplifier, showing all input, output, power, and control connections.
Close-up of the power and speaker output terminals on the Autotek MM2020.1D amplifier, including the 60A fuse.
Close-up of the input level, subsonic filter, low pass filter, bass boost, and RCA input/output connections on the Autotek MM2020.1D ampmai în viață.
Configurare și instalare
Conexiuni de alimentare
Connect the +12V terminal to the positive terminal of the car battery using appropriate gauge wire. Connect the -GND terminal to a solid chassis ground point. Ensure all connections are secure.
Conexiuni difuzoare
Connect your subwoofer(s) to the SPEAKER OUTPUT terminals. Ensure correct polarity (+ to + and - to -). This amplifier is designed for mono subwoofer systems.
Conexiuni de intrare / ieșire
Use RCA cables to connect the INPUT from your head unit or signal source. The OUTPUT RCA connections can be used to pass the audio signal to another ampmai în viață.
Pornire de la distanță
Connect the REM terminal to the remote turn-on output of your head unit. This will turn the amplifier on and off with your car's audio system.
Instalarea siguranței
The amplifier includes a 60A fuse. Ensure it is properly seated in its holder. Always replace with a fuse of the same rating.
Operațiunea
Reglarea nivelului de intrare
Adjust the INPUT LEVEL control (0.2V to 6V) to match the output voltage of your head unit. Start with the lowest setting and gradually increase until desired volume is achieved without distortion.
Filtru subsonic
Use the SUBSONIC FILTER control (10Hz to 40Hz) to filter out extremely low frequencies that are inaudible and can waste amplifier power. Adjust based on your subwoofer's capabilities.
Filtru trece jos
Adjust the LOW PASS filter (40Hz to 300Hz) to control the upper frequency limit of the amplifier's output, ensuring only bass frequencies are sent to the subwoofer.
Bass Boost
The BASS BOOST control (0dB to 12dB) allows for an increase in bass output at a specific frequency. Use sparingly to avoid distortion.
Indicatoare luminoase
- PUTERE (Green): Illuminates when the ampLifter-ul primește energie electrică și funcționează normal.
- PROTEJA (Red): Illuminates when the amplifier enters protection mode due to a fault (e.g., short circuit, overheating, low voltagși).
Întreţinere
To ensure optimal performance and longevity of your Autotek MM2020.1D amplifier, keep it free from dust and debris. Periodically check all wiring connections for tightness and corrosion. Avoid exposing the amplifier to excessive moisture or extreme temperatures.
Depanare
| Problemă | Cauza posibila | Soluţie |
|---|---|---|
| No Power (POWER LED off) | No +12V, GND, or REM connection | Check all power, ground, and remote wire connections. Verify fuse. |
| Amplifier in Protection Mode (PROTECT LED on) | Short circuit in speaker wiring, overheating, low voltage | Verificați dacă există scurtcircuite la cablajul difuzorului. Asigurați o ventilație adecvată. Verificați volumul sistemului electric al vehiculului.tage. |
| Fără ieșire de sunet | No input signal, incorrect gain setting, speaker wiring issue | Check RCA input cables. Adjust INPUT LEVEL. Verify speaker connections and polarity. |
| Sunet distorsionat | Input level too high, incorrect filter settings, damaged speakers | Reduce INPUT LEVEL. Adjust SUBSONIC FILTER and LOW PASS filter. Check speaker condition. |
Specificații
| Caracteristică | Caietul de sarcini |
|---|---|
| Model | MM2020.1D |
| Output Power (Bridged Mono @ 4 Ohms) | 2,000 wați x 1 |
| Output Power (Mono @ 4 Ohms) | 500 wați x 1 |
| Output Power (Mono @ 2 Ohms) | 1,000 wați x 1 |
| Numărul de canale | 1 (Monobloc) |
| Voltage | 6 volți (în funcțiune) |
| Dimensiuni articol (L x l x H) | 11.81 x 9.84 x 2.28 inci |
| Greutatea articolului | 454 grame |
| Tip material | Aliaj de aluminiu |
| Tip de montare | Montare la suprafață |
| garanție | 1 an |
| Componente incluse | Produs, Manual |
| UPC | 806576228042 |
Informații despre garanție
The Autotek MM2020.1D amplifier comes with a 1-year limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims. For full warranty terms and conditions, refer to the documentation included with your product or visit the official Autotek website-ul.
Sprijin
For technical assistance, troubleshooting, or warranty inquiries regarding your Autotek MM2020.1D amplifier, please visit the official Autotek website or contact their customer support department. Ensure you have your product model number (MM2020.1D) and proof of purchase available when seeking support.
