IBO OHI 25-60/180 Circulation Pump User Manual

1. Produs terminatview

The IBO OHI 25-60/180 circulation pump, also known as a heating pump, facilitates the movement of heating water within a heating system. This pump model features a manual 3-speed regulator, allowing for system adaptation. It is suitable for use in heating and air conditioning systems with fluid temperatures ranging from +2°C to +110°C.

Caracteristicile cheie includ:

• Manual 3-speed regulator for optimal system adaptation.
• Suitable for heating and air conditioning systems with fluid temperatures from +2°C to +110°C.
• Constructed with a ceramic shaft, graphite radial bearing, stainless steel bearing plate and rear pot, and a grey cast iron pump housing.
• Compact design for easy installation.
• Operație silențioasă.

Image 1: IBO OHI 25-60/180 Circulation Pump. This image displays the orange-colored pump unit with its black control panel, showing the speed selector and technical specifications. Two black rubber seals are visible at the bottom.

2. Informații de siguranță

Read all instructions carefully before installation and operation. Failure to follow these instructions may result in electric shock, fire, or serious injury.

• Siguranta electrica: Ensure the power supply is disconnected before any installation, maintenance, or repair work. All electrical connections must be performed by a qualified electrician in accordance with local regulations. The pump requires a 230V, 50Hz power supply.
• Temperatura apei: The pump handles fluid temperatures between +2°C and +110°C. Exercise caution when working with hot water to prevent burns.
• Presiune: The maximum operating pressure is 10 bar. Ensure the system components can withstand this pressure.
• Mediu de instalare: Install the pump in a dry, well-ventilated area, protected from frost and direct weather exposure.
• Echipament individual de protectie: Always wear appropriate personal protective equipment (e.g., gloves, safety glasses) during installation and maintenance.

3. Ghid de instalare

Proper installation is crucial for the pump's efficient and safe operation.

3.1 Verificări înainte de instalare

• Verify that the pump's specifications (voltage, frequency, pressure) match your system requirements.
• Ensure the installation location provides adequate space for mounting and future maintenance.
• Confirm that the piping system is clean and free of debris.

3.2 Montarea pompei

1. The pump has an installation length of 180 mm. Ensure sufficient space between pipe connections.
2. Install the pump in the return line of the heating system, if possible, to extend its lifespan by operating at lower temperatures.
3. Ensure the motor shaft is horizontal to allow for proper lubrication of the bearings.
4. Use the provided seals (gaskets) to ensure a watertight connection to the piping. The connection diameter is 1 1/2"/1".
5. Tighten all connections securely but avoid over-tightening.

3.3 Conexiune electrică

1. Ensure the main power supply is switched off at the circuit breaker.
2. Connect the pump to a 1 x 230 V, 50 Hz power supply.
3. The pump has an IP44 protection rating. Ensure the electrical connections are protected from moisture.
4. Follow the wiring diagram provided on the pump's terminal box cover.
5. Asigurați o împământare adecvată.

3.4 System Filling and Venting

1. After installation, fill the heating system with water.
2. Vent the system thoroughly to remove any trapped air. Air in the system can cause noise and reduce pump efficiency.
3. The pump may have a manual vent screw; open it carefully until water flows out, then close it.

4. Instrucțiuni de utilizare

The IBO OHI 25-60/180 pump features a manual 3-speed selector to adjust performance.

4.1 Pornirea inițială

1. Ensure the system is filled with water and properly vented.
2. Turn on the main power supply to the pump.
3. Select a speed setting using the rotary switch on the pump's control panel.

Setări de viteză 4.2

The pump offers three speed levels, each with different power consumption, maximum flow rate (Q max), and maximum head (H max):

• Nivelul I: 46 W power consumption, 22 l/min maximum flow, 3 m maximum head.
• Nivelul II: 63 W power consumption, 38 l/min maximum flow, 5 m maximum head.
• Nivelul III: 93 W power consumption, 55 l/min maximum flow, 6 m maximum head.

Adjust the speed setting based on the heating system's requirements to achieve optimal circulation and energy efficiency.

5. Întreținere

Regular maintenance ensures the longevity and efficient operation of your circulation pump.

5.1 Verificări de rutină

• Inspecție vizuală: Periodically check the pump for any signs of leaks, corrosion, or damage to the casing or electrical connections.
• Nivel de zgomot: Listen for any unusual noises during operation, which could indicate air in the system or a mechanical issue.
• Temperatură: Ensure the pump is not overheating.

5.2 Curățare

Păstrați exteriorul pompei curat și fără praf și resturi pentru a asigura o disipare corespunzătoare a căldurii.

5.3 Pregătire pentru iarnă (dacă este cazul)

If the heating system is to be shut down for an extended period in freezing temperatures, ensure the system, including the pump, is drained to prevent frost damage.

6. Depanare

This section provides guidance for common issues. For complex problems, consult a qualified technician.

7. Specificatii tehnice

8. Garanție și asistență

Information regarding the product warranty is not provided in the available data. For warranty claims, technical support, or spare parts inquiries, please contact the original seller or the manufacturer, 4U-Onlinehandel, directly. Keep your purchase receipt as proof of purchase.