1. Produs terminatview
The Sicce Ultrazero Flat Sucking Pump is designed for efficient removal of water from various areas, including flooded cellars, garages, and other spaces where minimal residual water is desired. This submersible pump is capable of reducing water levels down to 2-3 mm.
Caracteristici cheie:
- Capable of pumping water down to 2 mm residual level.
- Fully submersible design.
- Handles dirt particles up to 3 mm in size.
- Equipped with a 10-meter power cable.
- Features a practical carry handle for easy transport.
Figura 1: Pesteview of the Sicce Ultrazero Flat Sucking Pump.
2. Informații de siguranță
Read all safety warnings and instructions before operating the pump. Failure to follow these instructions may result in electric shock, fire, or serious injury.
- Deconectați întotdeauna pompa de la sursa de alimentare înainte de manipulare, curățare sau efectuarea oricărei operațiuni de întreținere.
- Asigurați-vă că sursa de alimentare voltage matches the pump's specifications (230 V/50 Hz).
- Do not operate the pump with a damaged power cord or plug. If damaged, it must be replaced by the manufacturer, service agent, or similarly qualified persons to avoid a hazard.
- Do not use the pump to handle flammable or explosive liquids.
- Țineți copiii și persoanele neautorizate departe de zona de operare.
- Asigurați-vă că pompa este complet scufundată în timpul funcționării pentru a preveni supraîncălzirea.
- Avoid running the pump dry for extended periods.
- This pump is designed for water only. Do not use it for other liquids without consulting the manufacturer.
3. Configurare și instalare
Follow these steps to properly set up your Ultrazero pump:
- Despachetați pompa: Carefully remove the pump and all accessories from the packaging. Inspect for any damage.
- Connect the Discharge Hose:
The pump features a 26.44 mm (3/4") AG pressure connection. Attach a suitable discharge hose (e.g., 20 mm (3/4") hose connection) to this outlet. Ensure the connection is secure to prevent leaks.
Figure 2: Close-up of the pump's discharge outlet and integrated carry handle.
- Poziționați pompa: Place the pump directly on the surface from which water needs to be removed. Ensure the pump is stable and upright. The flat base allows for efficient water removal down to minimal levels.
- Route the Discharge Hose: Direct the discharge hose to a suitable drainage area, ensuring the water will not flow back into the area being drained.
- Conexiune de alimentare: Plug the 10-meter power cable into a grounded 230 V/50 Hz electrical outlet. Ensure the outlet is protected by a Ground Fault Circuit Interrupter (GFCI) for added safety, especially in wet environments.
Figure 3: The flat base of the pump designed for low residual water levels.
4. Instrucțiuni de utilizare
The Ultrazero pump is designed for simple operation:
- Scufundați pompa: Ensure the pump is fully submerged in the water you wish to remove. The pump requires water to cool its motor and operate correctly.
- Începeți pomparea: Once submerged and connected to power, the pump will begin operating automatically. It does not feature a float switch, so manual monitoring is required for optimal use.
- Monitorizați nivelul apei: The pump will continue to operate until the water level reaches its minimum suction capability of 2-3 mm.
- Stop Pumping: To stop the pump, disconnect it from the power supply. It is recommended to disconnect the pump once the desired water level is reached or if the pump starts to run dry.
Figure 4: The Ultrazero pump effectively draining water from a small pool.
Figure 5: The pump in action on a flooded floor, demonstrating its low-level suction capability.
Figure 6: Illustration of the pump's ability to reduce water levels to approximately 2 mm.
5. Întreținere
Întreținerea regulată asigură longevitatea și performanța optimă a pompei dumneavoastră.
- curatenie: After each use, especially when pumping dirty water, rinse the pump thoroughly with clean water. This helps prevent sediment buildup.
- Verificați pentru reziduuri: Periodically check the pump's intake area for any debris (e.g., leaves, small stones) that might obstruct water flow. Remove any blockages carefully after disconnecting power.
- Verificarea cablului: Regularly inspect the power cable for cuts, abrasions, or other damage. Do not use the pump if the cable is damaged.
- Depozitare: When not in use, store the pump in a clean, dry place, protected from frost.
Figure 7: The pump can also be used for transferring water for tasks like garden watering from a rain barrel.
6. Depanare
If you encounter issues with your Ultrazero pump, refer to the following common problems and solutions:
| Problemă | Cauza posibila | Soluţie |
|---|---|---|
| Pompa nu pornește. | Fără alimentare. Cablu de alimentare deteriorat. Motor overload protection activated. | Verificați conexiunea de alimentare și priza. Inspect cable for damage; replace if necessary (by qualified personnel). Disconnect power, allow motor to cool, then reconnect. |
| Pompa funcționează, dar nu se evacuează apă. | Intake blocked. Discharge hose kinked or blocked. Airlock in pump. | Disconnect power, clear intake. Check and clear discharge hose. Briefly lift and lower the pump while submerged to release trapped air. |
| Performanță redusă de pompare. | Partial blockage. Impeller worn. | Disconnect power, clean pump intake and impeller area. Contactați serviciul de asistență pentru clienți pentru service. |
| Pompa se oprește pe neașteptate. | Overheating due to low water level or blockage. Defecțiune electrică. | Disconnect power, check water level and clear blockages. Allow to cool. Dacă problema persistă, contactați serviciul de asistență pentru clienți. |
If the problem persists after attempting these solutions, please contact Sicce customer support.
7. Specificatii tehnice
Detailed specifications for the Sicce Ultrazero Flat Sucking Pump, Model 925607:
| Caietul de sarcini | Valoare |
|---|---|
| Marca | Sicce |
| Numărul de model | 925607 |
| Max. Delivery Rate (Flow Rate) | 3000 l/h |
| Max. Înălțime de livrare | 3.1 m |
| Power Consumption (P1) | 80 W |
| Vol. De operaretage | 220-240V / 50Hz |
| Conductor Length (Power Cable) | 10 m (three-core, indoor and outdoor use) |
| Conexiune de presiune | 26.44 mm (3/4") AG |
| Diametrul conexiunii furtunului | 20 mm (3/4") |
| Max. Solids Size | 3 mm |
| Nivelul apei reziduale | Down to 2-3 mm |
| Dimensiuni produs (aprox.) | 140 mm (Diameter) x 160 mm (Height) / 5.5" x 6.3" |
| Greutatea articolului | 2.6 kg (5.72 lbs) |
| Comutator plutitor | Nu |
| Protecție la suprasarcină | No (Internal thermal protection may exist, but no external reset) |
| Origine | Fabricat in Italia |
Figure 8: Technical drawing illustrating the pump's dimensions and 3/4" GAS connection.
8. Garanție și asistență
For warranty information or technical support regarding your Sicce Ultrazero Flat Sucking Pump, please contact Sicce customer service. Keep your purchase receipt and model number (925607) handy when contacting support.
Producător: Ebara
Marca: Sicce
For further assistance, visit the official Sicce website-ul sau contactați distribuitorul local.
