TEMPO Communications 468 Wiremap Tester Instruction Manual

Introducere

The TEMPO Communications 468 Wiremap Tester is designed to quickly and accurately verify the wiring integrity of LAN, telephone patch cords, and structured cabling. It identifies common wiring faults such as opens, shorts, reversals, and transposed pairs. The tester consists of a transmitter and a receiver unit, providing clear, simple-to-understand results through sequencing LEDs.

Informații de siguranță

• Do not connect the tester to live AC power circuits.
• The unit is protected against active circuits up to 52 VDC / 90V p-p for up to 10 minutes (Transmitter) and 52 VDC momentary (Receiver).
• Use only the specified battery type (9V).
• Scoateți bateria dacă unitatea nu va fi utilizată pentru o perioadă lungă de timp.

Conținutul pachetului

Verificați dacă toate elementele sunt prezente:

• 468T Transmitter Unit
• 468R Receiver Unit
• Husă de transport

Image shows the TEMPO Communications 468T Transmitter and 468R Receiver units, connected by a short patch cable, resting in their black carrying case.

Produs terminatview

Transmițător 468T

The transmitter unit initiates the test sequence and tone generation. It features an 8-position modular jack for connecting cables and LED indicators for T568A, USOC, and T568B wiring configurations. An ON/OFF switch controls power.

A închide view of the TEMPO Communications 468T Transmitter, showing the T568A, USOC, T568B labels, the "468T TRANSMITTER" text, four green LED indicators (1, 2, 3, 4), and the ON/OFF switch.

Receptor 468R

The receiver unit completes the test circuit and displays the results. It also has an 8-position modular jack and LED indicators (1, 2, 3, 4) that show normal (green) or reversed (red) wiring.

A închide view of the TEMPO Communications 468R Receiver, showing the T568A, USOC, T568B labels, the "468R RECEIVER" text, four LED indicators (1, 2, 3, 4) with "GREEN=NORM. RED=REV." legend.

Înființat

Instalarea bateriei

The 468 Wiremap Tester requires one 9V battery (not included) for operation in each unit.

1. Localizați compartimentul bateriilor pe spatele unităților emițător și receptor.
2. Deschideți capacul compartimentului bateriei.
3. Connect a 9V battery to the battery clip, observing polarity.
4. Introduceți bateria în compartiment și închideți bine capacul.

Note: Remove batteries if the unit is not in use for extended periods to prevent leakage.

Instrucțiuni de operare

Wiremap Testing

The 468 Wiremap Tester can test T568A, T568B (AT&T 258A/10 Base T), and USOC wiring configurations.

1. Ensure a 9V battery is installed in both the Transmitter and Receiver units.
2. Connect one end of the cable to be tested into the 8-position modular jack on the 468T Transmitter.
3. Connect the other end of the cable into the 8-position modular jack on the 468R Receiver.
4. Turn the 468T Transmitter ON using the ON/OFF switch. The test process activates automatically upon connection of the receiver.
5. Observe the sequencing red and green LEDs on both units.
6. Interpret the results based on the LED patterns:
• Cablare normală: All LEDs on both units will light up sequentially in green, indicating correct pin-to-pin continuity.
• Circuit deschis: If an LED fails to light up, it indicates an open circuit on that specific wire pair.
• Scurt circuit: If multiple LEDs light up simultaneously or in an incorrect sequence, it indicates a short circuit between those wire pairs.
• Reversed Pairs: LEDs on the receiver will light up red for reversed pairs.
• Transposed Pairs: Incorrect sequencing of green LEDs on the receiver indicates transposed pairs.
7. After testing, turn the 468T Transmitter OFF.

Tone Generation for Cable Identification

The 468 Wiremap Tester can generate a tone to help identify cables at remote locations.

1. Connect any 8-position modular plug of the cable to be identified into the appropriate jack on the 468T Transmitter.
2. Turn the 468T Transmitter ON. A sweeping tone signal (850 and 950 Hz alternating nominal) will be applied to all pairs.
3. At the far end of the cable, use a compatible inductive amplifier (probe, not included) to locate the corresponding cable by detecting the tone.
4. After identification, turn the 468T Transmitter OFF.

Depanare

Întreţinere

Curatenie

Ștergeți unitatea cu un dispozitiv moale, damp pânză. Nu utilizați agenți de curățare abrazivi sau solvenți.

Depozitare

Store the tester in its carrying case in a cool, dry place when not in use. Remove the 9V battery if storing for extended periods.

Specificații

Garanție și suport

Informații despre garanție

This TEMPO Communications 468 Wiremap Tester comes with a one-year warranty from the date of purchase. Please retain your proof of purchase for warranty claims. The warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from misuse, accidents, unauthorized modifications, or improper battery installation.

Asistență pentru clienți

For technical assistance or warranty inquiries, please visit the official TEMPO Communications website-ul sau contactați departamentul de servicii pentru clienți.

Visit the TEMPO Communications Store on Amazon